LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2022 >> CX-5 Turbo Signature >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 9 (On-Board Diagnostic - Engine Control System (VIN M) (4 Of 7)) >> DTC P0524-00: Engine Oil Pressure Too Low >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different variant/trim than selected.
DTC P0524-00: (PCM, VIN M) DIAGNOSTIC PROCEDURE

STEP INSPECTION RESULTS ACTION
1 RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
NOTE:
  • Recording can be facilitated using the screen capture function of the PC.
  • Record the snapshot data on the repair order.
 - Go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
 Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 INSPECT ENGINE OIL LEAKAGE
  • Start the engine.
  • Verify that there is no engine oil leakage in the hydraulic circuit.
  • Is there any leakage?
 Yes Repair or replace the malfunctioning part according to the inspection results, then add genuine engine oil.
(See ENGINE OIL REPLACEMENT [VIN M] ).
No Go to the next step.
4 INSPECT ENGINE OIL LEVEL
 Yes Go to the next step.
No Add genuine engine oil.
(See ENGINE OIL REPLACEMENT [VIN M] ).
5 INSPECT ENGINE OIL TEMPERATURE SENSOR/ENGINE OIL PRESSURE SENSOR CONNECTOR CONDITION
  • Switch the ignition off.
  • Disconnect the engine oil temperature sensor/engine oil pressure sensor connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 11.
No Go to the next step.
6 INSPECT ENGINE OIL SOLENOID VALVE CONNECTOR CONDITION
  • Disconnect the engine oil solenoid valve connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 11.
No Go to the next step.
7 INSPECT PCM CONNECTOR CONDITION
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 11.
No Go to the next step.
8 INSPECT ENGINE OIL TEMPERATURE SENSOR/ENGINE OIL PRESSURE SENSOR OR ENGINE OIL SOLENOID VALVE CIRCUIT FOR SHORT TO GROUND
  • Verify that the engine oil temperature sensor/engine oil pressure sensor, engine oil solenoid valve and PCM connectors are disconnected.
  • Inspect for continuity between the following terminals (wiring harness-side) and body ground:
    • Engine oil temperature sensor/engine oil pressure sensor terminal A
    • Engine oil temperature sensor/engine oil pressure sensor terminal D
      • Engine oil solenoid valve terminal B
  • Is there continuity?
 Yes Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
  • Engine oil temperature sensor/engine oil pressure sensor terminal A-PCM terminal 1D
  • Engine oil temperature sensor/engine oil pressure sensor terminal D-PCM terminal 1AS
  • Engine oil solenoid valve terminal B-PCM terminal 1CK

    If there is a common connector:

    • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
      • Repair or replace the malfunctioning part.

    If there is no common connector:

    • Repair or replace the wiring harness which has a short to ground.

    Go to Step 11.
No Go to the next step.
9 INSPECT ENGINE OIL PRESSURE SENSOR
 Yes Replace the engine oil pressure sensor, then go to the next step.
(See ENGINE OIL TEMPERATURE SENSOR/ENGINE OIL PRESSURE SENSOR REMOVAL/INSTALLATION [VIN M] ).
No Go to the next step.
10 INSPECT ENGINE OIL SOLENOID VALVE
 Yes Replace the engine oil solenoid valve, then go to the next step.
(See ENGINE OIL SOLENOID VALVE REMOVAL/INSTALLATION [VIN M] ).
No Replace the oil pump, then go to the next step.
(See OIL PUMP REMOVAL/INSTALLATION [VIN M] ).
11 VERIFY DTC TROUBLESHOOTING COMPLETED
  • Always reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC ).
  • Start the engine.
  • Increase and keep the engine speed at 2, 500 rpm for 5 s.
  • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST ).
  • Is the same Pending DTC present?
 Yes Repeat the inspection from Step 1.
No Go to the next step.
12 VERIFY AFTER REPAIR PROCEDURE
 Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals