LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2022 >> CX-30 Preferred >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Body Panels >> Front Bumper Removal/Installation [(Us)]

Front Bumper Removal/Installation [(Us)]

  1. Affix the protective tape to the position (vehicle body side) shown in the figure to prevent scratches and damage.
    G14489500Courtesy of MAZDA MOTORS CORP.
  2. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)] .)
  3. Remove the upper face. (See UPPER FACE REMOVAL/INSTALLATION .)
  4. Remove the fasteners.
    G14489501Courtesy of MAZDA MOTORS CORP.
  5. Pull the front over fender in the direction of the arrow shown in the figure and disengage the clips shown in the figure.
    G14489502Courtesy of MAZDA MOTORS CORP.
  6. Remove the screws and fasteners.
    G14489503Courtesy of MAZDA MOTORS CORP.
  7. Remove the bolts and fasteners which can be verified at the position where front under cover No. 1 was pulled back.
    Fig 1: Front Under Cover No. 1, Front Bumper And Bolts With Torque Specification
    G14489504Courtesy of MAZDA MOTORS CORP.
  8. Partially peel back the front deflector.
    G14489505Courtesy of MAZDA MOTORS CORP.
  9. Disconnect the connectors.
  10. Remove the wiring harness clips.
  11. Remove the screws.
    Fig 2: Front Bumper Screws With Torque Specification
    G14489506Courtesy of MAZDA MOTORS CORP.
  12. Remove the fasteners.
    CAUTION:
    • Carefully remove the front bumper from the front bumper slider No. 1. If the front bumper is removed from the front bumper slider No. 1 with excessive force, the front bumper hooks may be damaged because the front bumper and the front bumper slider No. 1 are engaged firmly.
    • Detach the front bumper hooks from the front bumper slider No. 1 using two people, one person supports the front bumper. If the front bumper hooks are detached from the front bumper without supporting the front bumper, it may fall off and be damaged.
  13. Pull the rear end of the front bumper in the order of the arrows shown in the figure, and detach the front bumper hooks from the front bumper slider No. 1.
    G14489507Courtesy of MAZDA MOTORS CORP.
  14. Pull the front bumper in the direction of the arrows shown in the figure.
    G14489508Courtesy of MAZDA MOTORS CORP.
  15. Disconnect the connectors.
    G14489509Courtesy of MAZDA MOTORS CORP.
  16. Remove the wiring harness clip.
  17. Remove the front bumper.
  18. Install in the reverse order of removal.
  19. Perform the 360° view monitor system aiming. (with 360° view monitor system) (See 360° VIEW MONITOR SYSTEM AIMING .)
  20. Perform the front radar sensor aiming adjustment. (with front radar sensor) (See FRONT RADAR SENSOR AIMING .)
    CAUTION:
    • If there is foreign matter on the front center brand emblem at the position shown in the figure, the aiming cannot be performed correctly. Before performing the aiming, verify that there are no stickers, water, mud, or dirt on the front center brand emblem.
    G14489510Courtesy of MAZDA MOTORS CORP.
  21. Perform the front side radar sensor aiming adjustment. (with front side radar sensor) (See FRONT SIDE/REAR SIDE RADAR SENSOR AIMING .)
CAUTION:
  • If there is foreign matter on the front bumper, the aiming cannot be performed correctly. Before performing the aiming, verify that there are no stickers, water, mud, or dirt on the front bumper.
scientia non olet · About LEMON Manuals