| 1 |
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
NOTE:
- Recording can be facilitated using the screen capture function of the PC.
- Record the snapshot data on the repair order.
|
- |
Go to the next step. |
| 2 |
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
- Verify related Service Bulletins and/or on-line repair information availability.
- Is any related repair information available?
|
Yes |
Perform repair or diagnosis according to the available repair information.
- If the vehicle is not repaired, go to the next step.
|
| No |
Go to the next step. |
| 3 |
INSPECT WASTEGATE VALVE CONNECTOR CONDITION
- Switch the ignition off.
- Disconnect the wastegate valve connector.
- Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
- Is there any malfunction?
|
Yes |
Repair or replace the connector and/or terminals, then go to Step 9. |
| No |
Go to the next step. |
| 4 |
INSPECT WASTEGATE VALVE POSITION SENSOR CIRCUIT FOR SHORT TO GROUND
- Verify that the wastegate valve connector is disconnected.
- Inspect for continuity between the following terminals (wiring harness-side) and body ground:
- Wastegate valve terminal A
- Wastegate valve terminal E
- Is there continuity?
|
Yes |
Disconnect the PCM connector and inspect the wiring harness for short to ground.
- If the short to ground circuit could be detected in the wiring harness:
- Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- Wastegate valve terminal A-PCM terminal 1CF
- Wastegate valve terminal E-PCM terminal 1BJ
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to ground.
- If the short to ground circuit could not be detected in the wiring harness:
|
| No |
Go to the next step. |
| 5 |
INSPECT PCM CONNECTOR CONDITION
- Disconnect the PCM connector.
- Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
- Is there any malfunction?
|
Yes |
Repair or replace the connector and/or terminals, then go to Step 9. |
| No |
Go to the next step. |
| 6 |
INSPECT WASTEGATE VALVE POSITION SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER
- Verify that the wastegate valve and PCM connectors are disconnected.
- Inspect for continuity between wastegate valve terminals E and C (wiring harness-side).
- Is there continuity?
|
Yes |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- Wastegate valve terminal E-PCM terminal 1BJ
- Wastegate valve terminal C-PCM terminal 1AR
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.
- Repair or replace the malfunctioning part. If there is no common connector:
- Repair or replace the wiring harness which has a short to each other.
Go to Step 9.
|
| No |
Go to the next step. |
| 7 |
INSPECT WASTEGATE VALVE POSITION SENSOR POWER SUPPLY CIRCUIT FOR OPEN CIRCUIT
- Verify that the wastegate valve and PCM connectors are disconnected.
- Inspect for continuity between wastegate valve terminal A (wiring harness-side) and PCM terminal 1CF (wiring harness-side).
- Is there continuity?
|
Yes |
Go to the next step. |
| No |
Refer to the wiring diagram and verify whether or not there is a common connector between wastegate valve terminal A and PCM terminal 1CF.
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
- Repair or replace the malfunctioning part. If there is no common connector:
- Repair or replace the wiring harness which has an open circuit.
Go to Step 9. |
| 8 |
INSPECT WASTEGATE VALVE
POSITION SENSOR
|
Yes |
Replace the dynamic pressure turbo (DPT), then go to the next step.
(See DYNAMIC PRESSURE TURBO REMOVAL/INSTALLATION [VIN Y]
.) |
| No |
Go to the next step. |
| 9 |
VERIFY DTC TROUBLESHOOTING COMPLETED
- Always reconnect all disconnected connectors.
- Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC
.)
- Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST
.)
- Is the same Pending DTC present?
|
Yes |
Repeat the inspection from Step 1.
Go to the next step. |
| No |
Go to the next step. |
| 10 |
VERIFY AFTER REPAIR PROCEDURE
|
Yes |
Go to the applicable DTC inspection.
(See DTC TABLE .) |
| No |
DTC troubleshooting completed. |