LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-5 Sport, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 22 (On-Board Diagnostic - Engine Control (VIN Y) (1 Of 3)) >> DTC P004C-00: Three Way Solenoid Valve Control Circuit Low Input >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different variant/trim than selected.
DTC P004C:00 (PCM, VIN Y) DIAGNOSTIC PROCEDURE

STEP INSPECTION RESULTS ACTION
1 RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
NOTE:
  • Recording can be facilitated using the screen capture function of the PC.
  • Record the snapshot data on the repair order.
 - Go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
 Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 INSPECT THREE WAY SOLENOID VALVE CONNECTOR CONDITION
  • Switch the ignition off.
  • Disconnect the three way solenoid valve connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 9.
No Go to the next step.
4 INSPECT THREE WAY SOLENOID VALVE POWER SUPPLY CIRCUIT FOR SHORT TO GROUND OR OPEN CIRCUIT
  • Verify that the three way solenoid valve connector is disconnected.
  • Switch the ignition ON (engine off).
    NOTE:
    • Another DTC may be stored by the PCM detecting an open circuit.
  • Measure the voltage at the three way solenoid valve terminal A (wiring harness-side).
  • Is the voltage B+?
 Yes Go to the next step.
No Inspect the ENGINE1 15 A fuse.
  • If the fuse is blown:
    • Refer to the wiring diagram and verify whether or not there is a common connector between ENGINE1 15 A fuse and three way solenoid valve terminal A.

If there is a common connector:
  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
  • Repair or replace the malfunctioning part.

If there is no common connector:
  • Repair or replace the wiring harness which has a short to ground.
    • Replace the fuse.
    • If the fuse is damaged:
      • Replace the fuse.
  • If the fuse is normal:
    • Refer to the wiring diagram and verify whether or not there is a common connector between main relay terminal C and three way solenoid valve terminal A.

If there is a common connector:
  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
    • Repair or replace the malfunctioning part.

If there is no common connector:
  • Repair or replace the wiring harness which has an open circuit.

Go to Step 9.
5 INSPECT PCM CONNECTOR CONDITION
  • Switch the ignition off.
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 9.
No Go to the next step.
6 INSPECT THREE WAY SOLENOID VALVE CONTROL CIRCUIT FOR SHORT TO GROUND
  • Verify that the three way solenoid valve and PCM connectors are disconnected.
  • Inspect for continuity between three way solenoid valve terminal B (wiring harness-side) and body ground.
  • Is there continuity?
 Yes Refer to the wiring diagram and verify whether or not there is a common connector between three way solenoid valve terminal B and PCM terminal 1BH.
If there is a common connector:
  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
  • Repair or replace the malfunctioning part.

If there is no common connector:
  • Repair or replace the wiring harness which has a short to ground.

Go to Step 9.
No Go to the next step.
7 INSPECT THREE WAY SOLENOID VALVE CONTROL CIRCUIT FOR OPEN CIRCUIT
  • Verify that the three way solenoid valve and PCM connectors are disconnected.
  • Inspect for continuity between three way solenoid valve terminal B (wiring harness-side) and PCM terminal 1BH (wiring harness-side).
  • Is there continuity?
 Yes Go to the next step.
No Refer to the wiring diagram and verify whether or not there is a common connector between three way solenoid valve terminal B and PCM terminal 1BH.
If there is a common connector:
  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
  • Repair or replace the malfunctioning part.

If there is no common connector:
  • Repair or replace the wiring harness which has an open circuit.

Go to Step 9.
8 INSPECT THREE WAY SOLENOID VALVE
 Yes Replace the three way solenoid valve, then go to the next step.
(See THREE WAY SOLENOID VALVE REMOVAL/INSTALLATION [VIN Y] .)
No Go to the next step.
9 VERIFY DTC TROUBLESHOOTING COMPLETED
  • Always reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC .)
  • Perform the KOER self test. (See KOEO/KOER SELF TEST .)
  • Is the same Pending DTC present?
 Yes Repeat the inspection from Step 1.

Go to the next step.
No Go to the next step.
10 VERIFY AFTER REPAIR PROCEDURE
 Yes Go to the applicable DTC inspection.
(See DTC TABLE .)
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals