LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo Premium >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 27 (On-Board Diagnostic - Engine Control System (VIN L & VIN M) (3 Of 4)) >> DTC P189F:00 [Pcm (SKYACTIV-G)] >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different variant/trim than selected.
DTC P189F:00 (PCM, SKYACTIV-G) DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
  • Record the freeze frame data/snapshot data.
NOTE:
  • Recording can be facilitated using the screen capture function of the PC.
 - Go to the next step.
2 VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
  • Verify related Service Bulletins, on-line repair information, or Service Information availability.
  • Is any related Information available?
 Yes Perform repair or diagnosis according to the available information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 INSPECT ELECTRICAL SUPPLY UNIT (ESU) CONNECTOR FOR MALFUNCTION
  • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .)
  • Are the connector and terminal normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
4 INSPECT ELECTRICAL SUPPLY UNIT (ESU) POWER SUPPLY CIRCUIT FOR SHORT TO GROUND AND OPEN CIRCUIT
  • Inspect the power supply circuit for an open circuit and short to ground. (See CIRCUIT INSPECTION .)
  • Is the circuit normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
5 INSPECT ELECTRICAL SUPPLY UNIT (ESU) FOR MALFUNCTION DEPENDING ON REPEATABILITY
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
    • Switch the ignition ON (engine off)
  • Perform the DTC inspection for the PCM. (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)] .) If the CAN communication is normal, replace the electrical supply unit (ESU), perform the repair completion verification.
(See ELECTRICAL SUPPLY UNIT (ESU) REMOVAL/INSTALLATION .)
No Perform the repair completion verification 2.
Repair completion verification 1 VERIFY THAT VEHICLE IS REPAIRED
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
    • Switch the ignition ON (engine off)
  • Perform the DTC inspection for the PCM. (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)] .)
If the CAN communication is normal, perform the diagnosis from Step 1.
No Go to the next step.
Repair completion verification 2 VERIFY IF OTHER DTCs DISPLAYED
  • Perform the DTC inspection. (See DTC INSPECTION .)
  • Are any other DTCs displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals