LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 90 (On-Board Diagnostic - Body Control Module (BCM) (3 Of 3)) >> DTC P0850-24: Transaxle Range Sensor Circuit Malfunction (BCM) >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2020 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.
DTC P0850:24 (BCM) DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 VERIFY BODY CONTROL MODULE (BCM) DTCs AGAIN
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Switch the ignition ON (engine off).
  • Perform the following work 5 times or more.
  • Operate the selector lever to P or N position and wait for 1 s or more.
  • Operate the selector lever to other than P and N position and wait for 1 s or more.
    • Operate the selector lever to P or N position.
  • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Go to the next step.
No Go to repair completion verification 2.
2 INSPECT TCM FOR MALFUNCTION
  • Perform the DTC inspection for the TCM. (See DTC INSPECTION .)
  • Is a DTC displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [TCM (ET6A-EL, ET6AX-EL) (US)] .)
(See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [TCM (EV6A-EL, EV6AX-EL) (US)] .)
No Go to the next step.
3 INSPECT BODY CONTROL MODULE (BCM) CONNECTOR FOR MALFUNCTION
  • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .)
  • Are the connector and terminal normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
4 INSPECT TCM CONNECTOR FOR MALFUNCTION
  • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .)
  • Are the connector and terminal normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
5 INSPECT TCM SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY
  • Inspect the applicable circuit for a short to power supply. (See CIRCUIT INSPECTION .)
  • Is the circuit normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
6 INSPECT TCM FOR MALFUNCTION DEPENDING ON REPEATABILITY
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Switch the ignition ON (engine off).
  • Perform the following work 5 times or more.
  • Operate the selector lever to P or N position and wait for 1 s or more.
  • Operate the selector lever to other than P and N position and wait for 1 s or more.
    • Operate the selector lever to P or N position.
  • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, replace the TCM and perform the repair completion verification.
(See CONTROL VALVE BODY REMOVAL/INSTALLATION [ET6A-EL, ET6AX-EL (US)] .)
(See CONTROL VALVE BODY REMOVAL/INSTALLATION [EV6A-EL, EV6AX-EL (US)] .)
No Go to repair completion verification 2.
Repair completion verification 1 VERIFY THAT VEHICLE IS REPAIRED
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Switch the ignition ON (engine off).
  • Perform the following work 5 times or more.
  • Operate the selector lever to P or N position and wait for 1 s or more.
  • Operate the selector lever to other than P and N position and wait for 1 s or more.
    • Operate the selector lever to P or N position.
  • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, perform the diagnosis from Step 1.
No Go to the next step.
Repair completion verification 2 VERIFY IF OTHER DTC IS DISPLAYED
  • Perform the DTC inspection. (See DTC INSPECTION .)
  • Are any other DTCs displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals