LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 82 (On-Board Diagnostic - Airbag System) >> DTC B0001-11, B0001-12, B0001-13, B0001-19 Or B0001-1A: Driver-Side Air Bag Module (Inflator No. 1) Circuit (Airbag) (Us) >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2020 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.
DTC B0001:11 OR B0001:1A [SAS CONTROL MODULE] DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR No. 1) CONNECTOR
WARNING:
Yes Replace clock spring and perform the repair completion verification.
)
(See CLOCK SPRING REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)
No Go to the next step.
2 INSPECT CLOCK SPRING
  • Remove the clock spring. .) (See CLOCK SPRING REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)
  • Inspect for continuity between the following terminals:
    • Clock spring terminal 2A-Driver-side air bag module (inflator No. 1) terminal 1A
    • Clock spring terminal 2B-Driver-side air bag module (inflator No. 1) terminal 1B
    NOTE:
    • Inspect the clock spring wiring harness for continuity while shaking it.
  • Is there continuity?
 Yes Go to the next step.
No Replace clock spring and perform the repair completion verification.
(See CLOCK SPRING REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)
3 INSPECT CLOCK SPRING CIRCUIT FOR SHORT TO EACH OTHER
  • Clock spring connectors are disconnected.
  • Switch the ignition off.
  • Disconnect the negative battery terminal and wait for 1 min or more. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION (US) .)
  • Refer to the wiring diagram and inspect for continuity between driver-side air bag module (inflator No. 1) terminals and other clock spring terminals.
  • Is there continuity?
 Yes Replace clock spring and perform the repair completion verification.
(See CLOCK SPRING REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)
No Go to the next step.
4 INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR No. 1) DEPLOYMENT SIGNAL CIRCUIT FOR SHORT TO GROUND
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
5 INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR No. 1) DEPLOYMENT SIGNAL CIRCUIT FOR OPEN CIRCUIT
  • SAS control module and clock spring connectors are disconnected.
  • Inspect the driver-side air bag module (inflator No. 1) deployment signal circuit for open circuit. (See CIRCUIT INSPECTION .)
    NOTE:
    • Inspect for open circuit while shaking the wiring harness between the SAS control module and clock spring.
  • Is the circuit normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
6 INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR No. 1) DEPLOYMENT SIGNAL CIRCUIT FOR SHORT TO EACH OTHER
  • SAS control module and clock spring connectors are disconnected.
  • Inspect the driver-side air bag module (inflator No. 1) deployment signal circuit for short to each other. (See CIRCUIT INSPECTION .)
    NOTE:
    • Inspect for short to each other while shaking the wiring harness between the SAS control module and clock spring.
  • Is the circuit normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
7 INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR No. 1) DEPLOYMENT SIGNAL CIRCUIT FOR SHORT TO OTHER AIR BAG MODULE CIRCUIT
  • SAS control module and clock spring connectors are disconnected.
  • Other air bag module and pretensioner seat belt connectors are disconnected.
  • Refer to the wiring diagram and inspect for continuity between the following terminals and other air bag module/pre-tensioner seat belt terminals (wiring harness-side).
    • SAS control module terminal 1AM
    • SAS control module terminal 1AQ
    NOTE:
    • Inspect for continuity while shaking the wiring harness between the SAS control module and clock spring.
  • Is there continuity?
 Yes Repair or replace the malfunctioning location and perform the repair completion verification.
No Go to the next step.
8 INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR No. 1) DEPLOYMENT SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY
  • SAS control module and clock spring connectors are disconnected.
  • Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION (US) .)
  • Inspect the driver-side air bag module (inflator No. 1) deployment signal circuit for a short to power supply. (See CIRCUIT INSPECTION .)
    NOTE:
    • Inspect for a short to power supply while shaking the wiring harness between the SAS control module and clock spring.
  • Is the circuit normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
9 INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR No. 1)
  • Switch the ignition off.
  • Disconnect the negative battery terminal and wait for 1 min or more. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION (US) .)
  • Connect the SAS control module connectors.
  • Except for the driver-side air bag module (inflator No. 1) connector, reconnect all disconnected connectors.
  • Apply 2 ohms resistance to clock spring connector terminals 2A and 2B.
  • Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION (US) .)
  • Switch the ignition ON (engine off or on).
  • Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC .)
  • Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION .)
  • Are the same Pending DTCs present?
 Yes Go to the next step.
No Replace the driver-side air bag module and perform the repair completion verification.
 
(See DRIVER-SIDE AIR BAG MODULE REMOVAL [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .) (See DRIVER-SIDE AIR BAG MODULE INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)
Repair completion verification PERFORM SAS CONTROL MODULE DTC INSPECTION
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .) If the CAN communication is normal, perform the diagnosis from Step 1.
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals