Diagnostic Procedure

WARNING: This page is about a different car, the 2020 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.

DTC P0017:00 (PCM, SKYACTIV-G) DIAGNOSTIC PROCEDURE

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Record the freeze frame data/snapshot data. NOTE: Recording can be facilitated using the screen capture function of the PC.	-	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY Verify related Service Bulletins, on-line repair information, or Service Information availability. Is any related Information available?	Yes	Perform repair or diagnosis according to the available information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY EXHAUST VALVE TIMING MECHANISM INSTALLATION Verify the exhaust valve timing mechanism installation for the timing chain. Is the exhaust valve timing mechanism installed correctly?	Yes	Go to the next step.
3		No	Reinstall the timing chain correctly and perform the repair completion verification.
4	INSPECT TIMING CHAIN FOR MALFUNCTION Inspect the applicable part. (See TIMING CHAIN REMOVAL/INSTALLATION (VIN M) .) (See TIMING CHAIN REMOVAL/INSTALLATION (VIN L) .) Is the part normal?	Yes	Go to the next step.
4		No	Repair or replace the malfunctioning location and perform the repair completion verification.
5	INSPECT EXHAUST CAMSHAFT SPROCKET FOR MALFUNCTION Inspect the applicable part. (See TIMING CHAIN REMOVAL/INSTALLATION (VIN M) .) (See TIMING CHAIN REMOVAL/INSTALLATION (VIN L) .) Is the part normal?	Yes	Go to the next step.
5		No	Repair or replace the malfunctioning location and perform the repair completion verification.
6	INSPECT VALVE TIMING Inspect the valve timing. (See TIMING CHAIN REMOVAL/INSTALLATION (VIN M) .) (See TIMING CHAIN REMOVAL/INSTALLATION (VIN L) .) Is there any malfunction?	Yes	Adjust the valve timing properly and perform the repair completion verification. (See TIMING CHAIN REMOVAL/INSTALLATION (VIN M) .) (See TIMING CHAIN REMOVAL/INSTALLATION (VIN L) .)
6		No	Go to the next step.
7	INSPECT CKP SENSOR CONNECTOR FOR MALFUNCTION Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .) Are the connector and terminal normal?	Yes	Go to the next step.
7		No	Repair or replace the malfunctioning location and perform the repair completion verification.
8	INSPECT CKP SENSOR FOR FOREIGN MATTER Visually inspect the CKP sensor for foreign matter. (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION (VIN M) .) (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION (VIN L) .) Is there any foreign matter on the CKP sensor?	Yes	Remove the foreign matter from the CKP sensor and perform the repair completion verification.
8		No	Go to the next step.
9	INSPECT CKP SENSOR PULSE WHEEL Visually inspect the CKP sensor pulse wheel. Is there any damage or scratching on the CKP sensor pulse wheel?	Yes	Replace the CKP sensor pulse wheel and perform the repair completion verification.
9		No	Go to the next step.
10	INSPECT CKP SENSOR FOR MALFUNCTION Inspect the applicable part. (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION (VIN M) .) (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION (VIN L) .) Is the part normal?	Yes	Go to the next step.
10		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION (VIN M) .) (See CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION (VIN L) .)
11	INSPECT EXHAUST CMP SENSOR CONNECTOR FOR MALFUNCTION Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .) Are the connector and terminal normal?	Yes	Go to the next step.
11		No	Repair or replace the malfunctioning location and perform the repair completion verification.
12	INSPECT EXHAUST CMP SENSOR FOR FOREIGN MATTER Visually inspect the exhaust CMP sensor for foreign matter. (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION (VIN M) .) (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION (VIN L) .) Is there any foreign matter on the exhaust CMP sensor?	Yes	Remove the foreign matter from the exhaust CMP sensor and perform the repair completion verification.
12		No	Go to the next step.
13	INSPECT EXHAUST CMP SENSOR PULSE WHEEL Visually inspect the exhaust CMP sensor pulse wheel. Is there any damage or scratching on the exhaust CMP sensor pulse wheel?	Yes	Replace the exhaust CMP sensor pulse wheel and perform the repair completion verification.
13		No	Go to the next step.
14	INSPECT EXHAUST CMP SENSOR FOR MALFUNCTION Inspect the applicable part. (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION (VIN M) .) (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION (VIN L) .) Is the part normal?	Yes	Go to the next step.
14		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION (VIN M) .) (See CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION (VIN L) .)
15	INSPECT PCM CONNECTOR FOR MALFUNCTION Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .) Are the connector and terminal normal?	Yes	Go to the next step.
15		No	Repair or replace the malfunctioning location and perform the repair completion verification.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Replicate the vehicle conditions at the time the DTC was detected using the following procedure. Start the engine and warm it up completely. Perform the DTC inspection for the PCM. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION (VIN M) .) (See PCM REMOVAL/INSTALLATION (VIN L) .)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTCs DISPLAYED Perform the DTC inspection. (See DTC INSPECTION .) Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.