LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 62 (On-Board Diagnostic - Body Control Module (BCM) (1 Of 3)) >> DTC B0052-11: Passenger-Side Buckle Switch Circuit Malfunction (BCM) (Us) >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2020 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.
DTC B0052:11 (BCM) (US) DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 INSPECT PASSENGER-SIDE BUCKLE SWITCH CONNECTOR FOR MALFUNCTION
  • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .)
  • Are the connector and terminal normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
2 INSPECT SOPHISTICATED AIRBAG SENSOR (SAS) CONTROL MODULE CONNECTOR FOR MALFUNCTION
  • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .)
  • Are the connector and terminal normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
3 INSPECT PASSENGER-SIDE BUCKLE SWITCH FOR MALFUNCTION
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
4 INSPECT PASSENGER-SIDE BUCKLE SWITCH SIGNAL CIRCUIT FOR SHORT TO GROUND
  • Inspect the applicable circuit for a short to ground. (See CIRCUIT INSPECTION .)
  • Is the circuit normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
5 INSPECT SOPHISTICATED AIRBAG SENSOR (SAS) CONTROL MODULE FOR MALFUNCTION DEPENDING ON REPEATABILITY
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Unfasten the passenger-side seat belt.
  • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, repair or replace the malfunctioning location and perform the repair completion verification.
 
(See SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.] .)
No Go to repair completion verification 2.
Repair completion verification 1 VERIFY THAT VEHICLE IS REPAIRED
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Unfasten the passenger-side seat belt.
  • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, perform the diagnosis from Step 1.
No Go to the next step.
Repair completion verification 2 VERIFY IF OTHER DTC IS DISPLAYED
  • Perform the DTC inspection. (See DTC INSPECTION .)
  • Are any other DTCs displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
No DTC troubleshooting completed.


DTC B0052:11 (BCM) (US) DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 INSPECT PASSENGER-SIDE BUCKLE SWITCH CONNECTOR FOR MALFUNCTION
  • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .)
  • Are the connector and terminal normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
2 INSPECT SEAT WEIGHT SENSOR CONTROL MODULE CONTROL MODULE CONNECTOR FOR MALFUNCTION
  • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION .)
  • Are the connector and terminal normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
3 INSPECT PASSENGER-SIDE BUCKLE SWITCH FOR MALFUNCTION
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
4 INSPECT PASSENGER-SIDE BUCKLE SWITCH SIGNAL CIRCUIT (UPSTREAM) FOR SHORT TO GROUND
  • Inspect the applicable circuit for a short to ground. (See CIRCUIT INSPECTION .)
  • Is the circuit normal?
 Yes Go to the next step.
No Repair or replace the malfunctioning location and perform the repair completion verification.
5 INSPECT SEAT WEIGHT SENSOR CONTROL MODULE CONTROL MODULE FOR MALFUNCTION DEPENDING ON REPEATABILITY
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Unfasten the passenger-side seat belt.
  • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, repair or replace the malfunctioning location and perform the repair completion verification.
(See FRONT SEAT REMOVAL/INSTALLATION (US) .)
No Go to repair completion verification 2.
Repair completion verification 1 VERIFY THAT VEHICLE IS REPAIRED
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (See CLEARING DTC .)
  • Unfasten the passenger-side seat belt.
  • Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION .)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW (US) .)
If the CAN communication is normal, perform the diagnosis from Step 1.
No Go to the next step.
Repair completion verification 2 VERIFY IF OTHER DTC IS DISPLAYED
  • Perform the DTC inspection. (See DTC INSPECTION .)
  • Are any other DTCs displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals