LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 247 (On-Board Diagnostic - MAZDA Connect (5 Of 5)) >> DTC U2300-56: Configuration Data Of Body Control Module (BCM) Is Invalid [Connectivity Master Unit] >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2020 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.
DTC U2300:56 (CONNECTIVITY MASTER UNIT) DIAGNOSTIC PROCEDURE

Step Inspection Results Action
1 INSPECT BODY CONTROL MODULE (BCM) AND CONNECTIVITY MASTER UNIT (CMU) FOR MALFUNCTION
  • Perform the DTC inspection for the body control module (BCM) and the connectivity master unit (CMU). (Refer to the [DTC INSPECTION] in the appropriate service information)
  • Are any of the following DTCs displayed?
    • Code related to body control module (BCM) communication error, internal malfunction
      • Code related to internal malfunction of connectivity master unit (CMU)
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(Refer to the [DTC TABLE [BODY CONTROL MODULE (BCM)]] in the appropriate service information)
(See DTC TABLE [CONNECTIVITY MASTER UNIT (US)] .)
No Go to the next step.
2 VERIFY REPLACEMENT RECORD OF CONNECTIVITY MASTER UNIT (CMU)
  • Verify if the connectivity master unit (CMU) has been replaced before performing this troubleshooting procedure.
  • Has the connectivity master unit (CMU) been replaced?
 Yes After implementing the required servicing according to procedure when replacing a module, perform the repair completion verification.
(Refer to the [CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION] in the appropriate service information)
No Go to the next step.
3 VERIFY IF MALFUNCTION IS CAUSED BY BODY CONTROL MODULE (BCM) CONFIGURATION ERROR
  • Switch the ignition OFF and wait for 30 s or more.
  • Switch the ignition ON (engine off or on) and wait for 30 s or more.
  • Clear the DTC recorded in the memory. (Refer to the [CLEARING DTC] in the appropriate service information)
  • Perform the DTC inspection for the connectivity master unit (CMU). (Refer to the [DTC INSPECTION] in the appropriate service information)
  • Is the same Pending DTC present?
 Yes Go to the next step.
No Go to repair completion verification 2.
4 VERIFY BODY CONTROL MODULE (BCM) CONFIGURATION RELATED DTCs
  • Clear the DTC recorded in the memory. (Refer to the [CLEARING DTC] in the appropriate service information)
  • Perform the DTC inspection for the body control module (BCM). (Refer to the [DTC INSPECTION] in the appropriate service information)
  • Is a configuration related DTC displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
(Refer to the [DTC TABLE [BODY CONTROL MODULE (BCM)]] in the appropriate service information)
No Go to the next step.
5 RESET CONFIGURATION DATA FOR BODY CONTROL MODULE (BCM)
  • Using the M-MDS, perform the body control module (BCM) configuration. (Refer to the [CONFIGURATION] in the appropriate service information)
  • Clear the DTC recorded in the memory. (Refer to the [CLEARING DTC] in the appropriate service information)
  • Perform the DTC inspection for the connectivity master unit (CMU). (Refer to the [DTC INSPECTION] in the appropriate service information)
  • Is the same Pending DTC present?
 Yes Replace the connectivity master unit (CMU) and perform the repair completion verification.
(Refer to the [CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION] in the appropriate service information)
No Go to repair completion verification 2.
Repair completion verification 1 VERIFY THAT VEHICLE IS REPAIRED
  • Install/connect the part removed/disconnected during the troubleshooting procedure.
  • Clear the DTC recorded in the memory. (Refer to the [CLEARING DTC] in the appropriate service information)
  • Perform the DTC inspection for the connectivity master unit (CMU). (Refer to the [DTC INSPECTION] in the appropriate service information)
  • Is the same Pending DTC present?
 Yes Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(Refer to the [CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW] in the appropriate service information)
If the CAN communication is normal, perform the diagnosis from Step 1.
  • If the malfunction recurs, replace the body control module (BCM), then go to the next step. (Refer to the [BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION] in the appropriate service information)
No Go to the next step.
Repair completion verification 2 VERIFY IF OTHER DTCs ARE DISPLAYED
  • Perform the DTC inspection. (Refer to the [DTC INSPECTION] in the appropriate service information)
  • Is a DTC displayed?
 Yes Repair the malfunctioning location according to the applicable DTC troubleshooting.
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals