LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> CX-30 Turbo Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 103 (On-Board Diagnostic - Parking Assist Unit (Optical)) >> PID/Data Monitor Table

PID/Data Monitor Table

WARNING: This page is about a different car, the 2020 Mazda CX-30. However, it is still accessible from the selected car via links, so may be relevant.

-: Not applicable

PID/DATA MONITOR DESCRIPTION (PARKING ASSIST UNIT (OPTICAL))

PID Unit/Operation Data contents Module control terminal
BCAM_AIM_ANS NONE/COMPLETE/ERROR
  • NONE: Rear mount camera aiming is not performed.
  • COMPLETE: Rear mount camera aiming is completed.
  • ERROR: Rear mount camera aiming is not completed correctly.
 -
BCAM_AIM_ANS_2 NONE/COMPLETE/ERROR
  • NONE: Rear mount camera aiming is not performed.
  • COMPLETE: Differences between aiming result of rear mount camera and configuration data is normal.
  • ERROR: Differences between aiming result of rear mount camera and configuration data is not normal.
 -
BCAM_AIM_ERROR_CODE Factory Aiming: Completed/Factory Aiming: ECU Internal Error/Factory Aiming: Front Camera Power Supply Error/Factory Aiming: Rear Camera Power Supply Error/Factory Aiming: Left Camera Power Supply Error/Factory Aiming: Right Camera Power Supply Error/Factory Aiming: Front Camera Image Signal Error/Factory Aiming: Rear Camera Image Signal Error/Factory Aiming: Left Camera Image Signal Error/Factory Aiming: Right Camera Image Signal Error/Factory Aiming: Left Front Door Open/Factory Aiming: Left Rear Door Open/Factory Aiming: Right Front Door Open/Factory Aiming: Right Rear Door Open/Factory Aiming: Trunk/Liftgate Open/Factory Aiming: Neither "PARKED" Nor "NEUTRAL"/Factory Aiming: Front Camera Target A Not Detected/Factory Aiming: Front Camera Target B Not Detected/Factory Aiming: Rear Camera Target G Not Detected/Factory Aiming: Rear Camera Target H Not Detected/Factory Aiming: Left Camera Target C Not Detected/Factory Aiming: Left Camera Target E Not Detected/Factory Aiming: Right Camera Target D Not Detected/Factory Aiming: Right Camera Target F Not Detected/Factory Aiming: Front Camera Analysis Error/Factory Aiming: Rear Camera Analysis Error/Factory Aiming: Left Camera Analysis Error/Factory Aiming: Right Camera Analysis Error/Dealer Aiming: Aiming Success/Dealer Aiming: Right Marker for Rear Camera Not Found/Dealer Aiming: Left Marker for Rear Camera Not Found/Dealer Aiming: Rear Marker for Left Camera Not Found/Dealer Aiming: Front Marker for Left Camera Not Found/Dealer Aiming: Left Marker for Front Camera Not Found/Dealer Aiming: Right Marker for Front Camera Not Found/Dealer Aiming: Front Marker for Right Camera Not Found/Dealer Aiming: Rear Marker for Right Camera Not Found/Dealer Aiming: Aiming Result Exceeds the Limit/Dealer Aiming: Aiming Not Performed Dealer Aiming: Aiming Failed by Internal Memory Error/Dealer Aiming: Rear Camera Image Not Input/Dealer Aiming: Left Camera Image Not Input/Dealer Aiming: Front Camera Image Not Input/Dealer Aiming: Right Camera Image Not Input/Dealer Aiming: Power Supply Error to Camera(s) Displays detected error code after performing rear mount camera aiming -
BCAM_AIM_ERROR_CODE_2 Factory Aiming: Completed/Factory Aiming: ECU Internal Error/Factory Aiming: Front Camera Power Supply Error/Factory Aiming: Rear Camera Power Supply Error/Factory Aiming: Left Camera Power Supply Error/Factory Aiming: Right Camera Power Supply Error/Factory Aiming: Front Camera Image Signal Error/Factory Aiming: Rear Camera Image Signal Error/Factory Aiming: Left Camera Image Signal Error/Factory Aiming: Right Camera Image Signal Error/Factory Aiming: Left Front Door Open/Factory Aiming: Left Rear Door Open/Factory Aiming: Right Front Door Open/Factory Aiming: Right Rear Door Open/Factory Aiming: Trunk/Liftgate Open/Factory Aiming: Neither "PARKED" Nor "NEUTRAL"/Factory Aiming: Front Camera Target A Not Detected/Factory Aiming: Front Camera Target B Not Detected/Factory Aiming: Rear Camera Target G Not Detected/Factory Aiming: Rear Camera Target H Not Detected/Factory Aiming: Left Camera Target C Not Detected/Factory Aiming: Left Camera Target E Not Detected/Factory Aiming: Right Camera Target D Not Detected/Factory Aiming: Right Camera Target F Not Detected/Factory Aiming: Front Camera Analysis Error/Factory Aiming: Rear Camera Analysis Error/Factory Aiming: Left Camera Analysis Error/Factory Aiming: Right Camera Analysis Error/Dealer Aiming: Aiming Success/Dealer Aiming: Right Marker for Rear Camera Not Found/Dealer Aiming: Left Marker for Rear Camera Not Found/Dealer Aiming: Rear Marker for Left Camera Not Found/Dealer Aiming: Front Marker for Left Camera Not Found/Dealer Aiming: Left Marker for Front Camera Not Found/Dealer Aiming: Right Marker for Front Camera Not Found/Dealer Aiming: Front Marker for Right Camera Not Found/Dealer Aiming: Rear Marker for Right Camera Not Found/Dealer Aiming: Aiming Result Exceeds the Limit/Dealer Aiming: Aiming Not Performed Dealer Aiming: Aiming Failed by Internal Memory Error/Dealer Aiming: Rear Camera Image Not Input/Dealer Aiming: Left Camera Image Not Input/Dealer Aiming: Front Camera Image Not Input/Dealer Aiming: Right Camera Image Not Input/Dealer Aiming: Power Supply Error to Camera(s) Displays detected error code after detecting differences between aiming result of rear mount camera and configuration data -
BCAM_DIF_X mm Displays difference between design value of rear mount camera installation position (x-axis) and rear mount camera installation position (x-axis) after aiming -
BCAM_DIF_Y mm Displays difference between design value of rear mount camera installation position (y-axis) and rear mount camera installation position (y-axis) after aiming -
BCAM_DIF_Z mm Displays difference between design value of rear mount camera installation position (z-axis) and rear mount camera installation position (z-axis) after aiming -
FCAM_AIM_ANS
NOTE:
  • Displays in the M-MDS but it does not operate.
FCAM_AIM_ANS_2
NOTE:
  • Displays in the M-MDS but it does not operate.
FCAM_AIM_ERROR_CODE
NOTE:
  • Displays in the M-MDS but it does not operate.
FCAM_AIM_ERROR_CODE_2
NOTE:
  • Displays in the M-MDS but it does not operate.
FCAM_DIF_X
NOTE:
  • Displays in the M-MDS but it does not operate.
FCAM_DIF_Y
NOTE:
  • Displays in the M-MDS but it does not operate.
FCAM_DIF_Z
NOTE:
  • Displays in the M-MDS but it does not operate.
LCAM_AIM_ANS
NOTE:
  • Displays in the M-MDS but it does not operate.
LCAM_AIM_ANS_2
NOTE:
  • Displays in the M-MDS but it does not operate.
LCAM_AIM_ERROR_CODE
NOTE:
  • Displays in the M-MDS but it does not operate.
LCAM_AIM_ERROR_CODE_2
NOTE:
  • Displays in the M-MDS but it does not operate.
LCAM_DIF_X
NOTE:
  • Displays in the M-MDS but it does not operate.
LCAM_DIF_Y
NOTE:
  • Displays in the M-MDS but it does not operate.
LCAM_DIF_Z
NOTE:
  • Displays in the M-MDS but it does not operate.
RCAM_AIM_ANS
NOTE:
  • Displays in the M-MDS but it does not operate.
RCAM_AIM_ANS_2
NOTE:
  • Displays in the M-MDS but it does not operate.
RCAM_AIM_ERROR_CODE
NOTE:
  • Displays in the M-MDS but it does not operate.
RCAM_AIM_ERROR_CODE_2
NOTE:
  • Displays in the M-MDS but it does not operate.
RCAM_DIF_X
NOTE:
  • Displays in the M-MDS but it does not operate.
RCAM_DIF_Y
NOTE:
  • Displays in the M-MDS but it does not operate.
RCAM_DIF_Z
NOTE:
  • Displays in the M-MDS but it does not operate.
VPWR V Displays parking assist unit (optical) power supply voltage -
scientia non olet · About LEMON Manuals