Determination Procedure
CAUTION:
- When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals.
- When inspecting the connector, touch it with a paper clip or similar thin pin without directly inserting a tester probe into the terminal.
- Disconnect the negative battery terminal before performing any work that requires handling of connectors.
DETERMINING SHORT TO POWER SUPPLY LOCATION (CAN-BUS No. 4) (US) DIAGNOSTIC PROCEDURE
| Step | Inspection | Action | |
|---|---|---|---|
| 1 | INSPECT CAN LINE BETWEEN BODY CONTROL MODULE (BCM) AND CONNECTOR C-08 FOR SHORT TO POWER SUPPLY
|
Yes | Go to Step 3. |
| No | Go to the next step. | ||
| 2 | INSPECT BODY CONTROL MODULE (BCM) FOR SHORT TO POWER SUPPLY
|
Yes | Replace the body control module (BCM) because there is a short to the power supply in the body control module (BCM). (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION .) |
| No | Repair or replace the wiring harness between the body control module (BCM) and connector C-08 because the wiring harness is shorted to the power supply. | ||
| 3 | INSPECT CAN LINE BETWEEN CONNECTOR C-08 AND CONNECTOR C-59/C-69 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Repair or replace the wiring harness between connector C-08 and connector C-59/C-69 because the wiring harness is shorted to the power supply. | ||
| 4 | INSPECT CAN LINE BETWEEN CONNECTOR C-59/C-69 AND ELECTRICAL SUPPLY UNIT (ESU) FOR SHORT TO POWER SUPPLY
|
Yes | Go to Step 6. (with parking sensor system) Go to Step 11. (Hatchback-5HB (without parking sensor system)) Go to Step 14. (Sedan-4SD (without parking sensor system)) |
| No | Go to the next step. | ||
| 5 | INSPECT PARKING ASSIST UNIT (ULTRASONIC) FOR SHORT TO POWER SUPPLY
|
Yes | Replace the electrical supply unit (ESU) because there is a short to the power supply in the electrical supply unit (ESU). (See ELECTRICAL SUPPLY UNIT (ESU) REMOVAL/INSTALLATION .) |
| No | Repair or replace the wiring harness between the electrical supply unit (ESU) and connector C-59/C-69 because the wiring harness is shorted to the power supply. | ||
| 6 | INSPECT CAN LINE BETWEEN CONNECTOR C-58 AND CONNECTOR C-59/C-69 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Repair or replace the wiring harness between connector C-58 and connector C-59/C-69 because the wiring harness is shorted to the power supply. | ||
| 7 | INSPECT CAN LINE BETWEEN PARKING ASSIST UNIT (ULTRASONIC) AND CONNECTOR C-58 FOR SHORT TO POWER SUPPLY
|
Yes | Go to Step 9. |
| No | Go to the next step. | ||
| 8 | INSPECT PARKING ASSIST UNIT (ULTRASONIC) FOR SHORT TO POWER SUPPLY
|
Yes | Replace the parking assist unit (ultrasonic) because there is a short to the power supply in the parking assist unit (ultrasonic). (See PARKING ASSIST UNIT (ULTRASONIC) REMOVAL/INSTALLATION .) |
| No | Repair or replace the wiring harness between the parking assist unit (ultrasonic) and connector C-58 because the wiring harness is shorted to the power supply. | ||
| 9 | INSPECT CAN LINE BETWEEN REAR SIDE RADAR SENSOR (RH) AND CONNECTOR C-60/C-70 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Repair or replace the wiring harness between connector C-60/C-70 and connector C-58 because the wiring harness is shorted to the power supply. | ||
| 10 | INSPECT REAR SIDE RADAR SENSOR (RH) FOR SHORT TO POWER SUPPLY
|
Yes | Replace the rear side radar sensor (RH) because there is a short to the power supply in the rear side radar sensor (RH). (See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION .) |
| No | Repair or replace the wiring harness between the rear side radar sensor (RH) and connector C-60/C-70 because the wiring harness is shorted to the power supply. | ||
| 11 | INSPECT CAN LINE BETWEEN CONNECTOR C-68 AND CONNECTOR C-69 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Repair or replace the wiring harness between the connector C-68 and connector C-69 because the wiring harness is shorted to the power supply. | ||
| 12 | INSPECT CAN LINE BETWEEN CONNECTOR C-70 AND CONNECTOR C-68 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Repair or replace the wiring harness between the connector C-70 and connector C-68 because the wiring harness is shorted to the power supply. | ||
| 13 | INSPECT REAR SIDE RADAR SENSOR (RH) FOR SHORT TO POWER SUPPLY
|
Yes | Replace the rear side radar sensor (RH) because there is a short to the power supply in the rear side radar sensor (RH). (See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION .) |
| No | Repair or replace the wiring harness between the rear side radar sensor (RH) and connector C-70 because the wiring harness is shorted to the power supply. | ||
| 14 | INSPECT CAN LINE BETWEEN CONNECTOR C-66 AND CONNECTOR C-59 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Repair or replace the wiring harness between the connector C-66 and connector C-59 because the wiring harness is shorted to the power supply. | ||
| 15 | INSPECT JB No. 3 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Replace the JB No. 3 because there is a short to the power supply in the JB No. 3. | ||
| 16 | INSPECT CAN LINE BETWEEN CONNECTOR C-60 AND CONNECTOR C-67 FOR SHORT TO POWER SUPPLY
|
Yes | Go to the next step. |
| No | Repair or replace the wiring harness between the connector C-60 and connector C-67 because the wiring harness is shorted to the power supply. | ||
| 17 | INSPECT REAR SIDE RADAR SENSOR (RH) FOR SHORT TO POWER SUPPLY
|
Yes | Replace the rear side radar sensor (RH) because there is a short to the power supply in the rear side radar sensor (RH). (See REAR SIDE RADAR SENSOR REMOVAL/INSTALLATION .) |
| No | Repair or replace the wiring harness between the rear side radar sensor (RH) and connector C-60 because the wiring harness is shorted to the power supply. | ||