LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2021 >> 3 Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> On-Board Diagnostic - Door-Electrical Supply Unit >> PID/Data Monitor Table [Door-Electrical Supply Unit (Us)] >> Door-Electrical Supply Unit (driver's side)

Door-Electrical Supply Unit (driver's side)

-: Not applicable

PID/DATA MONITOR DESCRIPTION [DOOR-ELECTRICAL SUPPLY UNIT (US)]

PID Unit/Operation Data contents Module control terminal
AT_STRAGE_MIRROR_CSTMZ Not Adopted/Off/On  
  • Not Adopted: Personalization feature for power outer mirrors is not applicable.
  • Off: Personalization feature setting for power outer mirrors is off.
  • On: Personalization feature setting for power outer mirrors is on.
 1A, 1B
BSM_MIRROR_IND_CTRL_D Off/On  
  • Off: Blind spot monitoring (BSM) warning light (driver's side) is turned off.
  • On: Blind spot monitoring (BSM) warning light (driver's side) is turned on.
 3K
BSP_EV_WRNG_L no event/left warning event  
  • no event: Blind spot monitoring (BSM) warning lights are turned off.
  • left warning event: Blind spot monitoring (BSM) warning light (LH) is flashed and blind spot monitoring (BSM) warning light (RH) is turned off.
 1A, 1B
BSP_EV_WRNG_R no event/right warning event  
  • no event: Blind spot monitoring (BSM) warning lights are turned off.
  • right warning event: Blind spot monitoring (BSM) warning light (RH) is flashed and blind spot monitoring (BSM) warning light (LH) is turned off.
 1A, 1B
C_DOOR_LCK_SW_D OFF/Lock/Unlock  
  • OFF: Door lock switch (driver's side) is not in lock and unlock.
  • Lock: Door lock switch (driver's side) is in lock.
  • Unlock: Door lock switch (driver's side) is in unlock.
 3P
CRANKING_STAT Off/On  
  • Off: Body control module (BCM) does not control cranking at ignition switch ON.
  • On: Body control module (BCM) controls cranking at ignition switch ON.
 -
CRASH_SIG Unknown/Normal/Abnormal/Crash  
  • Unknown: Crash signal is not determined.
  • Normal: Crash signal is not received.
  • Abnormal: Error collision signal is received.
  • Crash: Crash signal is received.
 1A, 1B
CTSY_LAMP_CTRL_STAT  
NOTE:
  • Displays in the M-MDS but it does not operate.
DOOR_CTSY_LAMP  
NOTE:
  • Displays in the M-MDS but it does not operate.
DOOR_G_OPEN_CLOSE_REQ WindowStop/WindowOpen/WindowClose  
  • WindowStop: Not during front door glass and rear door glass operation.
  • WindowOpen: While front door glass and rear door glass are opening.
  • WindowClose: While front door glass and rear door glass are closing.
 1A, 1B
DOOR_LCK_CTRL_S TAT_D OFF/NormalLock/NormalUnlock/2StageUnlock/SuperLock  
  • OFF: All door lock actuators are not operated.
  • NormalLock: All door lock actuators are operated to lock.
  • NormalUnlock: All door lock actuators are operated to unlock.
  • 2StageUnlock: All door lock actuators are operated to 2-step unlocking function.
  • SuperLock: All door lock actuators are operated to double locking function (with double locking).
 2H, 2E, 2D
DOOR_LCK_MSG - Displays the code to unlock doors 1A, 1B
DOOR_LCK_ULCK_CTRL_D Not Drive/All Lock/All SuperLock/All UnLock/Only DrvUnLock/Return All Lock  
  • Not Drive: All door lock actuators are not operated.
  • All Lock: All door lock actuators are operated to lock.
  • All SuperLock: All door lock actuators are operated to double locking function (with double locking).
  • All UnLock: All door lock actuators are operated to unlock.
  • Only DrvUnLock: Driver's door unlock actuator is operated to unlock.
  • Return All Lock: Returns to normal lock condition from double locking function condition.
 -
DOOR_SW_F_D Off/On  
  • Off: Door latch switch (driver's side) is off.
  • On: Door latch switch (driver's side) is on.
 1P
DOOR_SW_QF_P Faulty/Undefined/Not within Specification/OK  
  • Faulty: Front door latch switch signal cannot be received.
  • Undefined: Front door latch switch undefined signal is received.
  • Not within Specification: Front door latch switch unspecified signal is received.
  • OK: Front door latch switch signal can be received normally.
 1A, 1B
DOOR_SW_QF_R Faulty/Undefined/Not within Specification/OK  
  • Faulty: Rear door latch switch signal cannot be received.
  • Undefined: Rear door latch switch undefined signal is received.
  • Not within Specification: Rear door latch switch unspecified signal is received.
  • OK: Rear door latch switch signal can be received normally.
 1A, 1B
DOOR_SW_STAT_F_P Door Closed/Door Ajar  
  • Door Closed: Front door (passenger's side) is closed.
  • Door Ajar: Front door (passenger's side) is open.
 1A, 1B
DOOR_SW_STAT_L/R Door Closed/Door Ajar  
  • Door Closed: Rear door (LH) is closed.
  • Door Ajar: Rear door (LH) is open.
 1A, 1B
DOOR_SW_STAT_R/R Door Closed/Door Ajar  
  • Door Closed: Rear door (RH) is closed.
  • Door Ajar: Rear door (RH) is open.
 1A, 1B
DOOR_SW_STAT_T/LGT Faulty/Undefined/Not within Specification/OK  
  • Faulty: Liftgate latch switch signal from electrical supply unit (ESU) cannot be received.
  • Undefined: Liftgate latch switch undefined signal from electrical supply unit (ESU) is received.
  • Not within Specification: Liftgate latch switch unspecified signal from electrical supply unit (ESU) is received.
  • OK: Liftgate latch switch signal from electrical supply unit (ESU) can be received normally.
 1A, 1B
DOOR_ULCK_REQ All Lock/All SuperLock/All UnLock/Not Drive/Only DrvUnLock/Return All Lock  
  • All Lock: All door lock actuators are operated to lock.
  • All SuperLock: All door lock actuators are operated to double locking function (with double locking).
  • All UnLock: All door lock actuators are operated to unlock.
  • Not Drive: All door lock actuators are not operated.
  • Only DrvUnLock: Driver's door unlock actuator is operated to unlock.
  • Return All Lock: Returns to normal lock condition from double locking function condition.
 1A, 1B
DRIVE_POS_STAT OFF/Completed/Reject/NoNeed  
  • OFF: Position memory system is off.
  • Completed: Adjustment to programmed position by position memory system is completed.
  • Reject: Adjustment to programmed position by position memory system is not possible.
  • NoNeed: Adjustment from current position is unnecessary.
 1A, 1B
DRIVER_NUM Driver 1 (Memory SW1)/Driver 2 (Memory SW2)/Driver 3 (Transmitter 1)/Driver 4 (Transmitter 2)/Driver 5 (Transmitter 3)/Driver 6 (Transmitter 4)/Driver 7 (Transmitter 5)/Driver 8 (Transmitter 6)  
  • Driver 1 (Memory SW1): Seat position programmed to memory 1 switch is called up.
  • Driver 2 (Memory SW2): Seat position programmed to memory 2 switch is called up.
  • Driver 3 (Transmitter 1): Seat position programmed to remote transmitter No. 1 is called up.
  • Driver 4 (Transmitter 2): Seat position programmed to remote transmitter No. 2 is called up.
  • Driver 5 (Transmitter 3: Seat position programmed to remote transmitter No. 3 is called up.
  • Driver 6 (Transmitter 4): Seat position programmed to remote transmitter No. 4 is called up.
  • Driver 7 (Transmitter 5): Seat position programmed to remote transmitter No. 5 is called up.
  • Driver 8 (Transmitter 6): Seat position programmed to remote transmitter No. 6 is called up.
 1A, 1B
ERASE_REQ No Action/Erase Request  
  • No Action: Deletion of programmed seat position is not necessary.
  • Erase Request: Deletion of programmed seat position is necessary.
 1A, 1B
FOLD_MIRROR_CTRL_D OFF/Open/Close  
  • OFF: Retract/return motor (driver's side) does not operate.
  • Open: Retract/return motor (driver's side) operates in the return direction.
  • Close: Retract/return motor (driver's side) operates in the retract direction.
 1A, 1B
GEAR_REVERSE Off/On  
  • Off: Shift lever is not operated to the reverse position.
  • On: Shift lever is operated to the reverse position.
 1A, 1B
ID_STAT_1 NotComplete/Complete  
  • NotComplete: Programming of remote transmitter ID data between body control module (BCM) and door-electrical supply unit is not completed.
  • Complete: Programming of remote transmitter ID data between body control module (BCM) and door-electrical supply unit is completed.
 -
ID_STAT_2 Unknown/NG/OK  
  • Unknown: Verification of remote transmitter ID data between body control module (BCM) and door-electrical supply unit cannot be determined.
  • NG: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and not determined to be programmed remote transmitter.
  • OK: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined to be programmed remote transmitter.
 -
ID_STAT_3 OK/NG  
  • OK: Door unlock request is received.
  • NG: Authorization of remote transmitter fails 3 times or more and acceptance of door unlock request is inhibited.
 -
ID_STAT_4 0/1/2/3 or More  
  • 0: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined to be programmed remote transmitter.
  • Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined not to be programmed remote transmitter 1 time.
  • Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined not to be programmed remote transmitter 2 times.
  • 3 or More: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined not to be programmed remote transmitter more than 3 times.
 -
ILLMMV1ODE Unknown/OFF, daylight mode/ON, daylight mode  
  • Unknown: Panel light illumination request signal is not determined.
  • OFF, daylight mode: Panel light illumination request signal is not received.
  • ON, daylight mode: Panel light illumination request signal is received.
 1A, 1B
ILLMI_POWER_CTRL_STAT OFF/ON Displays illumination power supply condition 1A, 1B
IND_ILLMI  
NOTE:
  • Displays in the M-MDS but it does not operate.
INDIRECTJLLMI Unknown/0%Fade out/100%Fade in/KINDIRECTILLUMRATE_DARK% Fade/KINDIRECTILLUMRATE_MEDIUM% Fade/KINDIRECTILLUMRATE_BLIGHT% Fade  
  • Unknown: Interior light illumination condition cannot be detected.
  • 0%Fade out: Interior light is off.
  • 100%Fade in: Interior light is on.
  • KINDIRECTILLUMRATE_DARK% Fade: Brightness of interior light illumination is dark.
  • KINDIRECTILLUMRATE_MEDIUM% Fade: Brightness of interior light illumination is normal.
  • KINDIRECTILLUMRATE_BLIGHT% Fade: Brightness of interior light illumination is bright.
 1A, 1B
LLINK_SW Unlock/Neutral/Lock/Failure  
  • Unlock: Front door lock-link switch (driver's side) is in unlock.
  • Neutral: Front door lock-link switch (driver's side) is not in lock and unlock.
  • Lock: Front door lock-link switch (driver's side) is in lock.
  • Failure: Front door lock-link switch (driver's side) has a malfunction.
 -
LLINK_SW_LCK_D Off/On  
  • Off: Front door lock-link switch (driver's side) is in unlock.
  • On: Front door lock-link switch (driver's side) is in lock.
 1I
LLINK_SW_ULCK_D Off/On  
  • Off: Front door lock-link switch (driver's side) is in lock.
  • On: Front door lock-link switch (driver's side) is in unlock.
 1G
MIRROR_ADJ_CTRL_STAT_D OFF/Up/Down/Left/Right Up/down adjustment motor (driver's side) and left/right adjustment motor (driver's side) output signal
  • OFF: Mirror surface adjustment door mirror motor (driver's side) is not operated in any direction.
  • Up: Up/down adjustment motor (driver's side) operates upward.
  • Down: Up/down adjustment motor (driver's side) operates downward.
  • Left: Left/right adjustment motor (driver's side) operates leftward.
  • Right: Left/right adjustment motor (driver's side) operates rightward.
 3A, 3D, 3L
MIRROR_ADJ_SEL_SW OFF/L Side ON/R Side ON  
  • OFF: Left/right selection switch is off.
  • L Side ON: Left selection switch is on.
  • R Side ON: Right selection switch is on.
 3AB
MIRROR_ADJ_SEL_SW_L OFF/ON  
  • OFF: Left selection switch illumination is not illuminated.
  • ON: Left selection switch illumination is illuminated.
 3N
MIRROR_ADJ_SEL_SW_R OFF/ON  
  • OFF: Right selection switch illumination is not illuminated.
  • ON: Right selection switch illumination is illuminated.
 3AA
MIRROR_ADJ_SW OFF/Up/Down/Left/Right  
  • OFF: All switches are turned off.
  • Up: Upward switch is turned on.
  • Down: Downward switch is turned on.
  • Left: Leftward switch is turned on.
  • Right: Rightward switch is turned on.
 3E
MIRROR_DEF_CTRL_STAT_D Off/On Heated outer mirror filaments output signal
  • Off: Heated outer mirror (driver's side) filaments are not heated to warm.
  • On: Heated outer mirror (driver's side) filaments are heated to warm.
 3M
MIRROR_FOLD_SW Off/On  
  • Off: Outer mirror automatic folding switch is not in AUTO position.
  • On: Outer mirror automatic folding switch is in AUTO position.
 3I
MIRROR_TURN_LAMP_CTRL_D Off/ON Side turn light output signal
  • Off: Side turn light (driver's side) is turned off.
  • On: Side turn light (driver's side) is turned on.
 3H
PNL_LGHT_CTRL_B_LVL % Displays brightness to turn on panel lights 1A, 1B
PNL_LGHT_CTRL_D IM_CANCEL Unknown/OFF/ON  
  • Unknown: Dimmer cancel signal is not determined.
  • OFF: Dimmer cancel signal is not received.
  • ON: Dimmer cancel signal is received.
 1A, 1B
POWER_STAT OFF/ACC/ON/CRANK  
  • OFF: Body control module (BCM) controls ignition switch off (lock).
  • ACC: Body control module (BCM) controls ignition switch ACC.
  • ON: Body control module (BCM) controls ignition switch ON (engine off).
  • CRANK: Body control module (BCM) controls cranking at ignition switch ON.
 1A, 1B
PWIND_CUT_SW Off/On  
  • Off: Power-cut switch is off.
  • On: Power-cut switch is on.
 3X
PWIND_MAIN_DO WN_SW_F_D OFF/ON/WaterImmersion  
  • OFF: Driver's switch is not operated for open operation by power window main switch.
  • ON: Driver's switch is operated for open operation by power window main switch.
  • WaterImmersion: Driver's switch is sunk in water.
 3Q
PWIND_MAIN_SW_F_D OFF/ManualUp/AutoUp/AutoDown/WaterImm ersion  
  • OFF: Driver's switch is not operated by power window main switch.
  • ManualUp: Driver's switch is operated for a manual close operation by power window main switch.
  • AutoUp: Driver's switch is operated for an auto close operation by power window main switch.
  • AutoDown: Driver's switch is operated for an auto operation by power window main switch.
  • Water immersion: Driver's switch is sunk in water.
 3T
PWIND_MAIN_SW_F_P OFF/ManualUp/AutoUp/ManualDown/AutoDo wn/GNDShort  
  • OFF: Passenger's side switch is not operated by power window main switch.
  • ManualUp: Passenger's side switch is operated for a manual close operation by power window main switch.
  • AutoUp: Passenger's side switch is operated for an auto close operation by power window main switch.
  • ManualDown: Passenger's side switch is operated for a manual open operation by power window main switch.
  • AutoDown: Passenger's side switch is operated for an auto operation by power window main switch.
  • GNDShort: Short to ground circuit malfunction is received from passenger's side switch.
 3U
PWIND_MAIN_SW_ILLMI Off/ON  
  • Off: Power window main switch illumination is not illuminated.
  • ON: Power window main switch illumination is illuminated.
 3G, 3S
PWIND_MAIN_SW_L/R OFF/ManualUp/AutoUp/ManualDown/AutoDo wn/GNDShort  
  • OFF: Rear side switch (LR) is not operated by power window main switch.
  • ManualUp: Rear side switch (LR) is operated for a manual close operation by power window main switch.
  • AutoUp: Rear side switch (LR) is operated for an auto close operation by power window main switch.
  • ManualDown: Rear side switch (LR) is operated for a manual open operation by power window main switch.
  • AutoDown: Rear side switch (LR) is operated for an auto operation by power window main switch.
  • GNDShort: Short to ground circuit malfunction is received from rear side switch (LR).
 3V
PWIND_MAIN_SW_R/R OFF/ManualUp/AutoUp/ManualDown/AutoDo wn/GNDShort  
  • OFF: Rear side switch (RR) is not operated by power window main switch.
  • ManualUp: Rear side switch (RR) is operated for a manual close operation by power window main switch.
  • AutoUp: Rear side switch (RR) is operated for an auto close operation by power window main switch.
  • ManualDown: Rear side switch (RR) is operated for a manual open operation by power window main switch.
  • AutoDown: Rear side switch (RR) is operated for an auto operation by power window main switch.
  • GNDShort: Short to ground circuit malfunction is received from rear side switch (RR).
 3W
PWIND_MOTOR_STAT_F_D OFF/Open/Close Front power window motor (driver's side) output signal
  • OFF: Front power window motor (driver's side) does not rotate.
  • Open: Front power window motor (driver's side) performs a open operation.
  • Close: Front power window motor (driver's side) performs a close operation.
 2J, 2B
PWIND_MOTOR_STAT_R_D OFF/Open/Close Rear power window motor (driver's side) output signal
  • OFF: Rear power window motor (driver's side) does not rotate.
  • Open: Rear power window motor (driver's side) performs a open operation.
  • Close: Rear power window motor (driver's side) performs a close operation.
 2J, 2B
PWIND_POS_COUNT_F_D Count Displays the number of rotation (front power window motor (driver's side)) 2I, 2C
PWIND_POS_COUNT_R_D Count Displays the number of rotation (rear power window motor (driver's side)) 2J, 2B
PWIND_SUB_DOWN_SW_R_D OFF/ON/WaterImmersion  
  • OFF: Rear power window subswitch (driver's side) is not operated for open operation.
  • ON: Rear power window subswitch (driver's side) is operated for open operation.
  • Water immersion: Rear power window subswitch (driver's side) is sunk in water.
 1N
PWIND_SUB_SW_ILLMI_R_D OFF/ON  
  • OFF: Rear power window subswitch (driver's side) illumination is not illuminated.
  • ON: Rear power window subswitch (driver's side) illumination is illuminated.
 1K
PWIND_SUB_SW_R_D OFF/ManualUp/AutoUp/AutoDown/WaterImm ersion  
  • OFF: Rear power window subswitch (driver's side) is not operated.
  • ManualUp: Rear power window subswitch (driver's side) is operated for a manual close operation.
  • AutoUp: Rear power window subswitch (driver's side) is operated for an auto close operation.
  • AutoDown: Rear power window subswitch (driver's side) is operated for an auto open operation.
  • WaterImmersion: Rear power window subswitch (driver's side) is sunk in water.
 1K
R_DEF_CTRL_STAT Rear defogger Off/Rear defogger On  
  • Rear defogger Off: Rear window defogger operation request signal from climate control unit is not received.
  • Rear defogger On: Rear window defogger operation request signal from climate control unit is received.
 1A, 1B
RECALL_REQ No Action/Recall Request  
  • No Action: Seat position recall is not requested.
  • Recall Request: Seat position recall is requested.
 1A, 1B
RECORD_REQ No Action/Record Request  
  • No Action: Seat position programming is not requested.
  • Record Request: Seat position programming is requested.
 1A, 1B
REMOTE_MIRROR_POS_X_D V Displays input value for variable resistance sensor of left/right adjustment motor (driver's side). 3Y
REMOTE_MIRROR_POS_Y_D V Displays input value for variable resistance sensor of up/down adjustment motor (driver's side). 3F
RES_CTRL_STAT Remote Start Off/Remote Start On  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
 1A, 1B
RLY_STAT_B3_B4 +B3/+B4  
  • +B3: Power is supplied from terminal 2M.
  • +B4: Power is supplied from terminal 2L.
 2L, 2M
ROOM_FUSE_STAT Without Room Fuse/With Room Fuse/Unused/Unknown Displays the F27 25 A fuse condition. 1A, 1B
SHIFT Invalid/Initial Value/1st/2nd/3rd/4th/5th/6th/7th/8th/9th/Ne utral/Reverse/Park/Unknown Hex/Invalid Hex  
  • lnvalid: Shift lever position signal has error.
  • Initial Value: Shift lever is between two positions.
  • 1st: Shift lever is in 1st position.
  • 2nd: Shift lever is in 2nd position.
  • 3rd: Shift lever is in 3rd position.
  • 4th: Shift lever is in 4th position.
  • 5th: Shift lever is in 5th position.
  • 6th: Shift lever is in 6th position.
  • 7th: -
  • 8th: -
  • 9th: -
  • Neutral: Shift lever is in N position.
  • Reverse: Shift lever is in R position.
  • Park: Shift lever is in P position.
  • Unknown Hex: Shift lever position is not determined.
  • Invalid Hex: Shift lever position signal has error.
 1A, 1B
TURN_IND_L OFF/ON  
  • OFF: Turn switch LH signal is not received.
  • ON: Turn switch LH signal is received.
 1A, 1B
TURN_IND_R OFF/ON  
  • OFF: Turn switch RH signal is not received.
  • ON: Turn switch RH signal is received.
 1A, 1B
TURN_LAMP_KODO_REQ OFF/ON  
  • OFF: Turn light request signal is not received.
  • ON: Turn light request signal is received.
 1A, 1B
VPWR V Displays voltage at door-electrical supply unit terminal 2K (power supply) 2K
VPWR_B2 V Displays voltage at door-electrical supply unit terminal 2N (power supply) 2N
VPWR_B3 V Displays voltage at door-electrical supply unit terminal 2M (power supply) 2M
VPWR_B4 V Displays voltage at door-electrical supply unit terminal 2L (power supply) 2L
scientia non olet · About LEMON Manuals