Snapshot data table

-: Not applicable

SNAPSHOT DATA DESCRIPTION

Snapshot data item

Unit

Data contents

Data read/use method

Corresponding data monitor items

AAT

°C

°F

Ambient temperature

APP_STATUS

Accelerator Pedal Off/Under20%/Over20%/FAIL

Accelerator pedal position status

CFG_STATUS

Config Complete/Not Configured/Config Error

Instrument cluster configuration status

ECT_STATUS

Under 0 degrees C/0 - Under 80 degrees C/Over 80 degrees C/FAIL

Engine coolant temperature status

IC_VPWR

Instrument cluster power supply voltage

When DTC is detected, instrument cluster displays power supply voltage value of instrument cluster in M-MDS.

VPWR

IG-ON_TIMER

hh:mm:ss ⁽¹⁾

Elapsed time since ignition was switched ON (engine off or on)

NOTE: The instrument cluster records the elapsed time since the ignition was switched ON (engine off or on).

When DTC is detected, instrument cluster displays elapsed time since ignition was switched ON (engine off or on) in M-MDS.

PWR_MODE_KEY

Key Out/Key Recently Out (Position 0)/Accessory (Position 1)/Post Ignition (Position 2)/Ignition On (Position 2)/Running (Position 2)/Running - Starting

Key Out: Ignition switched off
Key Recently Out (Position 0): Elapsed time within 3 s since ignition was switched off
Accessory (Position 1): Ignition is switched to ACC
Post Ignition (Position 2): Elapsed time within 3 s since ignition was switched ON (engine off or on)
Ignition On (Position 2): Ignition switched ON (engine off)
Running (Position 2): Ignition switched ON (engine on)
Running - Starting: Cranking condition

When DTC is detected, instrument cluster displays ignition switch status in M-MDS.

RPM_STATUS

Engine Stop/Under1500RPM/Over1500RPM/F AIL

Engine speed status

When DTC is detected, instrument cluster displays engine speed in M-MDS.

TACHOMTR

SHIFT_STATUS

P/N/D/R/FAIL

Selector lever position status

When DTC is detected, instrument cluster displays selector lever position in M-MDS.

TOTAL_DIST

Miles

Accumulated total traveled distance from completion of vehicle until instrument cluster detects DTC (Odometer value in instrument cluster)

The total traveled distance from which the instrument cluster detects DTCs to the present can be calculated by performing the following procedure.

Verify the odometer value in the instrument cluster.
Verify the snapshot data item TOTAL_DIST
Subtract 2 from 1.

TOTAL_TIME

hh:mm:ss ⁽¹⁾

Accumulated total elapsed time since vehicle completion until instrument cluster detects a DTC

When the ROOM fuse is removed, and the ignition is switched off, the time is not included in the elapsed time.

The elapsed time from which the instrument cluster detects DTCs to the present can be calculated by performing the following procedure.

Verify the instrument cluster PID item TOTAL_TIME.
Verify the snapshot data item TOTAL_TIME.
Subtract 2 from 1.

TOTAL_TIME

VPWR

Instrument cluster power supply voltage

VPWR

VSPD_STATUS

Stop/0-10km/h/Over10km/h/FAIL

Vehicle speed status

When DTC is detected, instrument cluster displays vehicle speed in M-MDS.

VSS ⁽²⁾

KPH

MPH

Vehicle speed

WU1_P ⁽²⁾

KPa

MPa

Tire pressure (wheel unit No. 1)

WU1_P

WU1_T ⁽²⁾

°C

°F

Tire air temperature (wheel unit No. 1)

WU1_T

WU2_P ⁽²⁾

KPa

MPa

Tire pressure (wheel unit No. 2)

WU2_P

WU2_T ⁽²⁾

°C

°F

Tire air temperature (wheel unit No. 2)

WU2_T

WU3_P ⁽²⁾

KPa

MPa

Tire pressure (wheel unit No. 3)

WU3_P

WU3_T ⁽²⁾

°C

°F

Tire air temperature (wheel unit No. 3)

WU3_T

WU4_P ⁽²⁾

KPa

MPa

Tire pressure (wheel unit No. 4)

WU4_P

WU4_T ⁽²⁾

°C

°F

Tire air temperature (wheel unit No. 4)

WU4_T

⁽¹⁾	The seconds may be indicated after the decimal point.

⁽²⁾	With Direct Tire Pressure Monitoring System (TPMS)