Active Command Modes Procedure

WARNING: This page is about a different variant/trim than selected.

Connect the M-MDS (IDS) to the DLC-2.
After the vehicle is identified, select the following items from the initialization screen of the IDS.
1. Select "Data Logger".
2. Select "Modules".
3. Select "4X4".
Select the simulation items from the PID table.
Perform the active command modes function, inspect the operations for each parts.
- If the operation of output parts cannot be verified after the active command mode inspection is performed, this could indicate the possibility of an open or short circuit, sticking, or operation malfunction in the output parts.

DTC Table

x: Applicable

-: Not applicable

DTC DESCRIPTION

DTC

AWD warning light illuminati on status

Diagnosis system component

Fail-safe

Drive cycle

Self test type⁽¹⁾

Memory function

Service Information

M-MDS

P164D:00

Illuminated

AWD CM configuration

X

-

C

X

(See DTC P164D:00 [ELECTRONIC AWD CONTROL SYSTEM] .)

P182F:00

Flashed

AWD CM

X

-

C

X

(See DTC P182F:00 [ELECTRONIC AWD CONTROL SYSTEM] .)

P187B:00

Illuminated

AWD CM

X

-

C

X

(See DTC P187B:00 [ELECTRONIC AWD CONTROL SYSTEM] .)

P1886:00

Illuminated

AWD CM

X

-

C

X

(See DTC P1886:00 [ELECTRONIC AWD CONTROL SYSTEM] .)

P1887:11

Illuminated

AWD solenoid circuit

X

-

C

X

(See DTC P1887:11/P1887:12/P1887:13/P1887:14 [ELECTRONIC AWD CONTROL SYSTEM] .)

P1887:12

Illuminated

AWD solenoid circuit

X

-

C

X

P1887:13

Illuminated

AWD solenoid circuit

X

-

C

X

P1887:14

Illuminated

AWD solenoid circuit

X

-

C

X

P1888:11

Illuminated

Differential oil temperature sensor circuit

X

-

C

X

(See DTC P1888:11/P1888:15 [ELECTRONIC AWD CONTROL SYSTEM] .)

P1888:15

Illuminated

Differential oil temperature sensor circuit

X

-

C

X

P188A:00

Flashed

AWD CM

X

-

C

X

(See DTC P188A:00 [ELECTRONIC AWD CONTROL SYSTEM] .)

U0001:88

-

CAN system communication error

X

-

C

X

(See DTC U0001:88/U0100:00/U0101:00/U0121:00 [ELECTRONIC AWD CONTROL SYSTEM] .)

U0100:00

-

Communication error to PCM

X

-

C

X

U0101:00

-

CAN system communication error

X

-

C

X

U0121:00

-

CAN system communication error

X

-

C

X

U0401:68

-

Signal error from PCM

X

-

C

X

(See DTC U0401:68 [ELECTRONIC AWD CONTROL SYSTEM] .)

U0402:68

-

Signal error from TCM

X

-

C

X

(See DTC U0402:68 [ELECTRONIC AWD CONTROL SYSTEM] .)

U0415:68

-

Signal error from DSC HU/CM

X

-

C

X

(See DTC U0415:68 [ELECTRONIC AWD CONTROL SYSTEM] .)

U2100:00

Illuminated

AWD CM configuration

X

-

C

X

(See DTC U2100:00 [ELECTRONIC AWD CONTROL SYSTEM] .)

⁽¹⁾	C: CMDTC self test