Diagnostic Procedure

WARNING: This page is about a different car, the 2016 Mazda CX-5. However, it is still accessible from the selected car via links, so may be relevant.

STEP	Inspection		Action
1	VERIFY FRONT BODY CONTROL MODULE (FBCM) DTCs AGAIN Clear front body control module (FBCM) DTCs using the M-MDS. (See CLEARING DTC [FRONT BODY CONTROL MODULE (FBCM)] .) Switch the ignition ON (engine off or on). Perform the front body control module (FBCM) DTC inspection using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)] .) Is DTC B1D06:11 displayed?	Yes	Go to the next step.
1		No	Go to Step 11.
2	INSPECT FRONT COMBINATION LIGHT (LH) CONNECTOR CONDITION Switch the ignition to off. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Disconnect the front combination light (LH) connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
2		No	Repair or replace the connector, then go to Step 10.
3	INSPECT POWER OUTER MIRROR (LH) CONNECTOR CONDITION Disconnect the power outer mirror (LH) connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
3		No	Repair or replace the connector, then go to Step 10.
4	INSPECT REAR TURN LIGHT (LH) CONNECTOR CONDITION Disconnect the rear turn light (LH) connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
4		No	Repair or replace the connector, then go to Step 10.
5	INSPECT FRONT BODY CONTROL MODULE (FBCM) CONNECTOR CONDITION Disconnect the front body control module (FBCM) connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
5		No	Repair or replace the connector, then go to Step 10.
6	INSPECT TURN LIGHT (LH) CONTROL CIRCUIT FOR SHORT TO GROUND Verify that the front combination light (LH), power outer mirror (LH), rear turn light (LH), and front body control module (FBCM) connectors are disconnected. Inspect for continuity between the following terminals (vehicle wiring harness side) and body ground. Front body control module (FBCM) terminal 2B Front body control module (FBCM) terminal 2F Front body control module (FBCM) terminal 2D Is there continuity?	Yes	Repair or replace the wiring harness, then go to Step 10.
6		No	Go to the next step.
7	INSPECT SIDE TURN LIGHT (LH) Inspect the side turn light (LH). (See SIDE TURN LIGHT INSPECTION .) Is the side turn light (LH) normal?	Yes	Go to the next step.
7		No	Replace the side turn light (LH), then go to Step 10. (See SIDE TURN LIGHT REMOVAL/INSTALLATION .)
8	PERFORM DTC INSPECTION AND VERIFY IF MALFUNCTIONING PART IS REAR TURN LIGHT (LH) Clear front body control module (FBCM) DTCs using the M-MDS. (See CLEARING DTC [FRONT BODY CONTROL MODULE (FBCM)] .) Switch the ignition ON (engine off or on). Perform the front body control module (FBCM) DTC inspection using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)] .) Is DTC B1D06:11 displayed?	Yes	Replace the rear turn light bulb (LH), then go to the next step. (See REAR TURN LIGHT BULB REMOVAL/INSTALLATION .)
8		No	Go to Step 11.
9	PERFORM DTC INSPECTION AND VERIFY IF MALFUNCTIONING PART IS FRONT TURN LIGHT (LH) Clear front body control module (FBCM) DTCs using the M-MDS. (See CLEARING DTC [FRONT BODY CONTROL MODULE (FBCM)] .) Switch the ignition ON (engine off or on). Perform the front body control module (FBCM) DTC inspection using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)] .) Is DTC B1D06:11 displayed?	Yes	Replace the front turn light bulb (LH), then go to the next step. (See PARKING/FRONT TURN LIGHT BULB REMOVAL/INSTALLATION [FRONT COMBINATION LIGHT (BULB TYPE)] .)
9		No	Go to Step 11.
10	VERIFY THAT REPAIRS HAVE BEEN COMPLETED Reconnect all the disconnected connectors. Reconnect the disconnected negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Clear front body control module (FBCM) DTCs using the M-MDS. (See CLEARING DTC [FRONT BODY CONTROL MODULE (FBCM)] .) Switch the ignition ON (engine off or on). Operate the turn switch in LH position. Perform the front body control module (FBCM) DTC inspection using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)] .) Is DTC B1D06:11 displayed?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the front body control module (FBCM), then go to the next step. (See FRONT BODY CONTROL MODULE (FBCM) REMOVAL/INSTALLATION .)
10		No	Go to the next step.
11	VERIFY IF OTHER DTCs DISPLAYED Are any other DTCs displayed?	Yes	Repair the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [FRONT BODY CONTROL MODULE (FBCM)] .)
11		No	DTC troubleshooting completed.