Diagnostic Assist Code "65" Switch Inspection
WARNING: This page is about a different car, the 2017 Mazda 3. However, it is still accessible from the selected car via links, so may be relevant.
- Input diagnostic assist code "65" according to diagnostic assist code input procedure. (See DIAGNOSTIC ASSIST CODE INPUT PROCEDURE .)
- Perform the steering switch inspection or commander switch inspection.NOTE:
- When the switch is operated, the switch operation content detected by the connectivity master unit is displayed in the center display.
- If the switch operation content previously detected is being displayed in the center display, newly detected content is added over it.
DIAGNOSTIC ASSIST CODE DESCRIPTIONInspection Display of center display Action - Launch the switch inspection mode.
- Operate each switch of the steering switch.
- Does the display in the center display correspond to each switch operation?
- ST-SW Talk Button Pressed: TALK switch is pressed
- ST-SW Talk Button Released: TALK switch is released
- ST-SW Pick-Up Button Pressed: Pick-Up switch is pressed
- ST-SW Pick-Up Button Released: Pick-Up switch is released
- ST-SW Hang-Up Button Pressed: Hang-Up switch is pressed
- ST-SW Hang-Up Button Released: Hang-Up switch is released
- ST-SW Volume + Button Pressed: VOLUME (+) switch is pressed
- ST-SW Volume + Button Released: VOLUME (+) switch is released
- ST-SW Volume - Button Pressed: VOLUME (-) switch is pressed
- ST-SW Volume - Button Released: VOLUME (-) switch is released
- ST-SW Seek + Button Pressed: Seek (+) switch is pressed
- ST-SW Seek + Button Released: SEEK (+) switch is released
- ST-SW Seek - Button Pressed: Seek (-) switch is pressed
- ST-SW Seek - Button Released: Seek (-) switch is released
Yes The steering switch is normal. No Inspect the steering switch.
(See STEERING SWITCH INSPECTION .)- If there is a malfunction:
- Replace the steering switch. (See STEERING SWITCH REMOVAL/INSTALLATION .)
- If the steering switch is normal:
- Replace the connectivity master unit. (See CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION .)
DIAGNOSTIC ASSIST CODE DESCRIPTIONInspection Display of center display Action - Launch the switch inspection mode.
- Operate each button and knob of the commander switch.
- Does the display in the center display correspond to each operation?
- Home Button Pressed: HOME button is pressed
- Home Button Released: HOME button is released
- Navi Button Pressed: NAV button is pressed
- Navi Button Released: NAV button is released
- Audio Button Pressed: AUDIO button is pressed
- Audio Button Released: AUDIO button is released
- Favorites Button Pressed: FAVORITE button is pressed
- Favorites Button Released: FAVORITE button is released
- Back Button Pressed: BACK button is pressed
- Back Button Released: BACK button is released
- Commander Pushed In: Commander knob is pressed
- Commander Released: Commander knob is released
- Tilt Up Pressed: Commander knob is tilted up
- Tilt Up Released: Commander knob is released from tilted up condition
- Tilt Right Pressed: Commander knob is tilted to the right
- Tilt Right Released: Commander knob is released from tilted right condition
- Tilt Down Pressed: Commander knob is tilted down
- Tilt Down Released: Commander knob is released from tilted down condition
- Tilt Left Pressed: Commander knob is tilted to the left
- Tilt Left Released: Commander knob is released from tilted left condition
- Commander Turned Clockwise: Commander knob is turned clockwise
- Commander Turned Counter Clockwise: Commander knob is turned counterclockwise
- Volume Knob Pushed In: Volume dial is pressed
- Volume Knob Released: Volume dial is released
- Volume Knob Turned Clockwise: Volume dial is turned clockwise
- Volume Knob Turned Counter Clockwise: Volume dial is turned counterclockwise
Yes Commander switch is normal. No Replace the commander switch.
(See COMMANDER SWITCH REMOVAL/INSTALLATION .) - Cancel the diagnostic assist function according to ending procedure. (See ENDING PROCEDURE .)