PID/DATA Monitor Table

WARNING: This page is about a different car, the 2016 Mazda CX-5. However, it is still accessible from the selected car via links, so may be relevant.

PID name (definition)	Unit/Condition	Operation condition (reference)	ACTION
BRAKE_SW	Off/On	Brake pedal released: Off Brake pedal depressed: On	Inspect the brake switch. (See BRAKE SWITCH INSPECTION .)
BRK_F_P_C (Calculated Value)	Pa, psi	Brake pedal depressed: Changes according to the brake fluid pressure	Inspect the brake fluid pressure sensor. (See BRAKE FLUID PRESSURE SENSOR INSPECTION .)
BRK_F_P_R (Raw Value)	Pa, psi
DDS_MODE	Not_Learned/Learning/Learned	During initialization: Not_Learned During learning: Learning Learning completed*: Learned	Perform the DTC inspection for the DSC HU/Control Module. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)] .)
DSC_OFF_SW	Off/On	TCS OFF switch is released: Off TCS OFF switch is depressed: On	Inspect the TCS OFF switch. (See TCS OFF SWITCH INSPECTION .)
DSC_ST	Off/On	During TCS OFF mode: Off Other than TCS OFF mode: On	Perform the DTC inspection for the DSC HU/Control Module. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)] .)
LAT_ACCL_C (Calculated Value)	G	Vehicle stopped or driving at constant speed: 0 G Cornering to left: Changes 0 G-positive Cornering to right: Changes 0 G-negative	Perform the DTC inspection for the SAS control module. (See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM] .) (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)
LAT_ACCL_R (Raw Value)	G
LON_ACCL_C (Calculated Value)	G	Vehicle stopped or driving at constant speed: 0 G Vehicle is driving at a acceleration: Changes 0 G-positive Vehicle is driving at a deceleration: Changes 0 G-negative	Perform the DTC inspection for the SAS control module. (See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM] .) (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)
LON_ACCL_R (Raw Value)	G
P_BRAKE_SW	Off/On	Electric parking brake is released: OFF Electric parking brake is applied: ON	Inspect the electric parking brake switch. (See ELECTRIC PARKING BRAKE SWITCH INSPECTION .)
PMP_MT	NOTE: Displays in the M-MDS but it does not operate.
PMP_MT_SP	NOTE: Displays in the M-MDS but it does not operate.
R_GEAR_SW	Off/On	Except shift/selector lever at R position: OFF Shift/selector lever at R position: ON	Inspect the PCM. (MTX) (See PCM INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Inspect the TCM. (ATX) (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL, FW6AX-EL] .)
STR_ANG_C (Calculated Value)	°	Steering wheel in neutral position (not turned): 0° Steering wheel turned to left: Changes 0°-positive Steering wheel turned to right: Changes 0°-negative NOTE: Constantly indicates 0° until the steering wheel angle neutral position determination by the DSC HU/Control Module is completed. The steering wheel angle neutral position determination by the DSC HU/Control Module is completed when the vehicle is driven in a straight line at a speed of 20 km/h or more for several seconds.	Perform the DTC inspection for the PCM, DSC HU/Control Module, and EPS Control Module. If a DTC is displayed after performing the DTC inspection for the PCM, DSC HU/Control Module, and EPS vv, repair the malfunctioning part according to the applicable DTC troubleshooting. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)] .) (See EPS CONTROL MODULE INSPECTION .) After performing the DTC inspection, perform the following procedures: Start the engine and drive the vehicle in a straight line at a speed of 20 km/h or more for several seconds. If an abnormal value is indicated after verifying the value of the STR_ANG_C again, replace the DSC HU/Control Module.
STR_ANG_R (Raw Value)	°	Steering wheel position when ignition is switched ON (engine off or on): 0° Steering wheel turned to left: Changes 0°-positive Steering wheel turned to right: Changes 0°-negative NOTE: The signal displayed in this item is a steering angle (relative angle) signal output from the EPS Control Module.	Inspect the following PID. STR_ANG (See EPS CONTROL MODULE INSPECTION .)
TPMS_TYPE	No_DDS/DDS+TOM_EU/DDS+TOM_US	TPMS not equipped: No_DDS TPMS equipped (Corresponding to European regulations): DDS+TOM_EU TPMS equipped (Corresponding to U.S. regulations): DDS+TOM_US	Perform the DTC inspection for the DSC HU/Control Module. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)] .)
V_INLET_LF	Off/On	Solenoid valve not activated: Off Solenoid valve activated: On	Inspect the DSC HU/Control Module. (See DSC HU/CONTROL MODULE INSPECTION .)
V_INLET_LR
V_INLET_RF
V_INLET_RR
V_OUTLET_LF
V_OUTLET_LR
V_OUTLET_RF
V_OUTLET_RR
V_STB_LF/RR	NOTE: Displays in the M-MDS but it does not operate.
V_STB_RF/LR	NOTE: Displays in the M-MDS but it does not operate.
V_TRC_LF/RR	NOTE: Displays in the M-MDS but it does not operate.
V_TRC_RF/LR	NOTE: Displays in the M-MDS but it does not operate.
VPWR_B_SOL	V	Ignition switched ON (engine off): Approx. 12.2 V Idling: Approx. 14.1 V	Inspect power supply circuit. (See DSC HU/CONTROL MODULE INSPECTION .)
VSPD	KPH, MPH	Vehicle stopped: 0 KPH, 0 MPH Vehicle running: Vehicle speed	Inspect the DSC HU/CM. (See DSC HU/CONTROL MODULE INSPECTION .)
WSPD_SEN_LF	KPH, MPH	Vehicle stopped: 0 KPH, 0 MPH Vehicle running: Vehicle speed	Inspect the front ABS wheel-speed sensor. (See FRONT ABS WHEEL-SPEED SENSOR INSPECTION .)
WSPD_SEN_LR			Inspect the rear ABS wheel-speed sensor. (See REAR ABS WHEEL-SPEED SENSOR INSPECTION [2WD] .) (See REAR ABS WHEEL-SPEED SENSOR INSPECTION [AWD] .)
WSPD_SEN_RF			Inspect the front ABS wheel-speed sensor. (See FRONT ABS WHEEL-SPEED SENSOR INSPECTION .)
WSPD_SEN_RR			Inspect the rear ABS wheel-speed sensor. (See REAR ABS WHEEL-SPEED SENSOR INSPECTION [2WD] .) (See REAR ABS WHEEL-SPEED SENSOR INSPECTION [AWD] .)
YAW_RATE_C (Calculated Value)	°/s	Vehicle stopped or driving straight: 0 °/s Cornering to left: Changes 0 °/s-positive Cornering to right: Changes 0 °/s-negative	Perform the DTC inspection for the SAS control module. (See DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM] .) (See DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM] .)
YAW_RATE_R (Raw Value)	°/s

After ignition is switched off, switch it ON (engine off or on) and verify.