Diagnostic Procedure

DIAGNOSTIC PROCEDURE DESCRIPTION

STEP	INSPECTION	RESULTS	ACTION
1	RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the FREEZE FRAME DATA/snapshot data on the repair order.	-	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT FUEL TANK PRESSURE SENSOR CONNECTOR CONDITION Switch the ignition off. Disconnect the fuel tank pressure sensor connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
3		No	Go to the next step.
4	INSPECT PCM CONNECTOR CONDITION Disconnect the PCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
4		No	Go to the next step.
5	INSPECT FUEL TANK PRESSURE SENSOR SIGNAL CIRCUIT FOR SHORT TO GROUND Verify that the fuel tank pressure sensor and PCM connectors are disconnected. Inspect for continuity between the following terminals (wiring harness-side) and body ground: Fuel tank pressure sensor terminal A Fuel tank pressure sensor terminal C Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Fuel tank pressure sensor terminal A-PCM terminal 2BB Fuel tank pressure sensor terminal C-PCM terminal 2Y If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. Go to Step 9.
5		No	Go to the next step.
6	INSPECT FUEL TANK PRESSURE SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER Verify that the fuel tank pressure sensor and PCM connectors are disconnected. Inspect for continuity between fuel tank pressure sensor terminals C and B (wiring harness-side). Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Fuel tank pressure sensor terminal C-PCM terminal 2Y Fuel tank pressure sensor terminal B-PCM terminal 2AJ If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to each other. Go to Step 9.
6		No	Go to the next step.
7	INSPECT FUEL TANK PRESSURE SENSOR CIRCUIT FOR OPEN CIRCUIT Verify that the fuel tank pressure sensor and PCM connectors are disconnected. Inspect for continuity between the following terminals (wiring harness-side): Fuel tank pressure sensor terminal A-PCM terminal 2BB Fuel tank pressure sensor terminal C-PCM terminal 2Y Is there continuity?	Yes	Go to the next step.
7		No	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Fuel tank pressure sensor terminal A-PCM terminal 2BB Fuel tank pressure sensor terminal C-PCM terminal 2Y If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to Step 9.
8	INSPECT FUEL TANK PRESSURE SENSOR Inspect the fuel tank pressure sensor. (See FUEL TANK PRESSURE SENSOR INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is there any malfunction?	Yes	Replace the charcoal canister, then go to the next step. (See CHARCOAL CANISTER REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
8		No	Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED Always reconnect all disconnected connectors. Clear the DTC from the PCM memory using t he M-MDS. (See CLEARING DTC [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Is the same DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Go to the next step.
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE". (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
10		No	DTC troubleshooting completed.