Diagnostic Procedure

DIAGNOSTIC PROCEDURE DESCRIPTION

STEP	INSPECTION	RESULTS	ACTION
1	IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA Perform the Freeze Frame PID Data Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Is the DTC P0069:00 on FREEZE FRAME DATA?	Yes	Go to the next step.
1		No	Go to the troubleshooting procedure for DTC on FREEZE FRAME DATA. (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
2	RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the FREEZE FRAME DATA/snapshot data on the repair order.	-	Go to the next step.
3	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
3		No	Go to the next step.
4	VERIFY RELATED PENDING CODE AND/OR DTC Switch the ignition off, then ON (engine off). Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Is the PENDING CODE/DTC P0107:00, P0108:00, P2228:00 or P2229:00 also present?	Yes	Go to the applicable PENDING CODE or DTC inspection. (See DTC P0107:00 [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) (See DTC P0108:00 [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) (See DTC P2228:00 [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) (See DTC P2229:00 [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
4		No	Go to the next step.
5	INSPECT MAP SENSOR Inspect the MAP sensor. (See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is there any malfunction?	Yes	Replace the MAP sensor/IAT sensor No. 2, then go to Step 7. (See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR/INTAKE AIR TEMPERATURE (IAT) SENSOR NO. 2 REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
5		No	Go to the next step.
6	INSPECT BARO SENSOR Inspect the BARO sensor. (See BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Is there any malfunction?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
6		No	Go to the next step.
7	VERIFY DTC TROUBLESHOOTING COMPLETED Always reconnect all disconnected connectors. Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Start the engine. Switch the ignition off and wait for 15 s or more. Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Is the PENDING CODE for this DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .) Go to the next step.
7		No	Go to the next step.
8	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE". (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
8		No	DTC troubleshooting completed.