Diagnostic Procedure

DTC B11FD-1F; KEYLESS ANTENNA (EXTERIOR, LF) CIRCUIT MALFUNCTION - DIAGNOSTIC PROCEDURE

Step	Inspection		Action
1	INSPECT FRONT OUTER HANDLE (LH) CONNECTOR CONDITION Switch the ignition off. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Disconnect the front outer handle (LH) connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
1		No	Repair or replace the connector, then go to Step 7.
2	INSPECT LF CONTROL UNIT CONNECTOR CONDITION Disconnect the LF control unit connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
2		No	Repair or replace the connector, then go to Step 7.
3	INSPECT KEYLESS ANTENNA (EXTERIOR, LF) CIRCUIT FOR SHORT TO GROUND Verify that the LF control unit and front outer handle (LH) connectors are disconnected. Inspect for continuity between the following terminals (wiring harness-side) and body ground: Front outer handle (LH) terminal B Front outer handle (LH) terminal E Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: LF control unit terminal O-Front outer handle (LH) terminal B LF control unit terminal Q-Front outer handle (LH) terminal E If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. Go to Step 7.
3		No	Go to the next step.
4	INSPECT KEYLESS ANTENNA (EXTERIOR, LF) CIRCUIT FOR OPEN CIRCUIT Verify that the LF control unit and front outer handle (LH) connectors are disconnected. Inspect for continuity between the following terminals (wiring harness-side): LF control unit terminal O-Front outer handle (LH) terminal B LF control unit terminal Q- Front outer handle (LH) terminal E Is there continuity?	Yes	Go to the next step.
4		No	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: LF control unit terminal O-Front outer handle (LH) terminal B LF control unit terminal Q-Front outer handle (LH) terminal E If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has an open circuit. Go to Step 7.
5	INSPECT LF CONTROL UNIT Inspect the LF control unit. (See LF CONTROL UNIT INSPECTION .) Is the LF control unit normal?	Yes	Go to the next step.
5		No	Replace the LF control unit, then go to Step 7. (See LF CONTROL UNIT REMOVAL/INSTALLATION .)
6	VERIFY IF MALFUNCTIONING LOCATION IS KEYLESS ANTENNA (EXTERIOR, LF) DEPENDING ON REPEATABILITY Always reconnect all disconnected connectors. Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Clear the DTC for the start stop unit using the M-MDS. (See CLEARING DTC [START STOP UNIT] .) Perform the following work: Switch the ignition off. Open the door (driver's side). Close all the doors and liftgate. Retrieve the start stop unit DTCs using the M-MDS. (See DTC INSPECTION [START STOP UNIT] .) Is the same DTC displayed?	Yes	Replace the front outer handle (LH), then Go to the next step. (See FRONT OUTER HANDLE REMOVAL/INSTALLATION .)
6		No	Go to Step 8.
7	VERIFY THAT REPAIRS HAVE BEEN COMPLETED Always reconnect all disconnected connectors. Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Clear the DTC for the start stop unit using the M-MDS. (See CLEARING DTC [START STOP UNIT] .) Perform the following work: Switch the ignition off. Open the door (driver's side). Close all the doors and liftgate. Retrieve the start stop unit DTCs using the M-MDS. (See DTC INSPECTION [START STOP UNIT] .) Is the same DTC displayed?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the start stop unit. (See START STOP UNIT REMOVAL/INSTALLATION .) Go to the next step.
7		No	Go to the next step.
8	VERIFY IF OTHER DTCs DISPLAYED Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [START STOP UNIT] .)
8		No	DTC troubleshooting completed.