Diagnostic Procedure

DIAGNOSTIC PROCEDURE

Step	Inspection		Action
1	VERIFY REAR BODY CONTROL MODULE (RBCM) DTCs AGAIN Clear the DTC for the rear body control module (RBCM) using the M-MDS. (See CLEARING DTC [REAR BODY CONTROL MODULE (RBCM)] .) Retrieve the rear body control module (RBCM) DTCs using the M-MDS. (See DTC INSPECTION [REAR BODY CONTROL MODULE (RBCM)] .) Is the same DTC displayed?	Yes	Go to the next step.
1		No	Go to Step 9.
2	INSPECT POWER WINDOW MAIN SWITCH CONNECTOR CONDITION Switch the ignition off. Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Disconnect the power window main switch connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
2		No	Repair or replace the connector, then go to Step 8.
3	INSPECT DOOR LOCK SWITCH (LH) Inspect the door lock switch (LH). (See DOOR LOCK SWITCH INSPECTION .) Is the door lock switch (LH) normal?	Yes	Go to the next step.
3		No	Replace the power window main switch, then go to Step 8. (See POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION .)
4	INSPECT DOOR LOCK SWITCH (RH) CONNECTOR CONDITION Disconnect the door lock switch (RH) connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
4		No	Repair or replace the connector, then go to Step 8.
5	INSPECT DOOR LOCK SWITCH (RH) Inspect the door lock switch (RH). (See DOOR LOCK SWITCH INSPECTION .) Is the door lock switch (RH) normal?	Yes	Go to the next step.
5		No	Replace the door lock switch (RH), then go to Step 8. (See DOOR LOCK SWITCH REMOVAL/INSTALLATION .)
6	INSPECT REAR BODY CONTROL MODULE (RBCM) CONNECTOR CONDITION Disconnect the rear body control module (RBCM) connector. Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. Is the connector normal?	Yes	Go to the next step.
6		No	Repair or replace the connector, then go to Step 8.
7	INSPECT FOR SHORT TO GROUND IN DOOR LOCK SWITCH CIRCUIT Verify that the power window main switch, door lock switch (LH) and rear body control module (RBCM) connectors are disconnected. Inspect for continuity between rear body control module (RBCM) terminal 3F (wiring harness-side) and body ground. Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: Rear body control module (RBCM) terminal 3F-Power window main switch terminal 1E Rear body control module (RBCM) terminal 3F-Door lock switch (RH) terminal C If there is a common connector: Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. Repair or replace the malfunctioning part. If there is no common connector: Repair or replace the wiring harness which has a short to ground. Go to the next step.
7		No	Go to the next step.
8	VERIFY THAT REPAIRS HAVE BEEN COMPLETED Always reconnect all disconnected connectors. Reconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .) Clear the DTC for the rear body control module (RBCM) using the M-MDS. (See CLEARING DTC [REAR BODY CONTROL MODULE (RBCM)] .) Retrieve the rear body control module (RBCM) DTCs using the M-MDS. (See DTC INSPECTION [REAR BODY CONTROL MODULE (RBCM)] .) Is the same DTC displayed?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the rear body control module (RBCM). (See REAR BODY CONTROL MODULE (RBCM) REMOVAL/INSTALLATION .) Go to the next step.
8		No	Go to the next step.
9	VERIFY IF OTHER DTCs DISPLAYED Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [REAR BODY CONTROL MODULE (RBCM)] .)
9		No	DTC troubleshooting completed.