LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2017 >> CX-5 Grand Select, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> On-Board Diagnostic - HS/Ms - Can >> Determining Short To Ground Location (Ms-Can) >> Determination Procedure

Determination Procedure

CAUTION:
  • When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals.
  • When inspecting the DLC-2, touch it with a paper clip or similar thin pin without directly inserting a tester into the terminals.
Step Inspection Action
1 INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-63 AND REAR BODY CONTROL MODULE (RBCM)
  • Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .)
  • Disconnect connector C-63.
  • Inspect for continuity at the following terminals:
    • Between DLC-2 terminal L and body ground
      • Between DLC-2 terminal K and body ground
  • Is there continuity?
 Yes Go to Step 5.
No Go to the next step.
2 INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-63 AND CLIMATE CONTROL UNIT
  • Inspect for continuity at the following terminals:
    • Between climate control unit terminal 1K and body ground (with full-auto air conditioner)
    • Between climate control unit terminal 1M and body ground (with full-auto air conditioner)
    • Between climate control unit terminal Q and body ground (with manual air conditioner)
      • Between climate control unit terminal S and body ground (with manual air conditioner)
  • Is there continuity?
 Yes Go to the next step.
No Go to Step 4.
3 INSPECT CAN LINE IN CLIMATE CONTROL UNIT FOR SHORT TO GROUND
  • Disconnect the climate control unit connector.
  • Inspect for continuity at the following terminals:
    • Between climate control unit terminal 1K (wiring harness side) and body ground (with full-auto air conditioner)
    • Between climate control unit terminal 1M (wiring harness side) and body ground (with full-auto air conditioner)
    • Between climate control unit terminal Q (wiring harness side) and body ground (with manual air conditioner)
      • Between climate control unit terminal S (wiring harness side) and body ground (with manual air conditioner)
  • Is there continuity?
 Yes Repair or replace the wiring harness between the climate control unit and connector C-63 because the wiring harness is shorted to ground.
No Replace the climate control unit because there is a short to ground in the climate control unit.
(See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER] .)
(See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER] .)
4 INSPECT CAN LINE IN INSTRUMENT CLUSTER FOR SHORT TO GROUND
  • Disconnect the instrument cluster connector.
  • Inspect for continuity at the following terminals:
    • Between instrument cluster terminal C (wiring harness side) and body ground
      • Between instrument cluster terminal E (wiring harness side) and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between the instrument cluster and connector C-63 because the wiring harness is shorted to ground.
No Replace the instrument cluster because there is a short to ground in the instrument cluster.
(See INSTRUMENT CLUSTER REMOVAL/INSTALLATION .)
5 INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-63 AND CONNECTOR C-64
  • Connect connector C-63.
  • Disconnect connector C-64.
  • Inspect for continuity at the following terminals:
    • Between instrument cluster terminal C and body ground
      • Between instrument cluster terminal E and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between connector C-63 and connector C-64 because the wiring harness is shorted to ground.
No Go to the next step.
6 INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-64 AND DLC-2
  • Inspect for continuity at the following terminals:
    • Between DLC-2 terminal L and body ground
      • Between DLC-2 terminal K and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between connector C-64 and DLC-2 because the wiring harness is shorted to ground.
No Go to the next step.
7 INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-64 AND CONNECTOR C-14
  • Disconnect connector C-14.
  • Connect connector C-64.
  • Inspect for continuity at the following terminals:
    • Between DLC-2 terminal L and body ground
      • Between DLC-2 terminal K and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between connector C-64 and connector C-14 because the wiring harness is shorted to ground.
No Go to the next step.
8 INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-14 AND CONNECTOR C-71
  • Disconnect connector C-71.
  • Connect connector C-14.
  • Inspect for continuity at the following terminals:
    • Between DLC-2 terminal L and body ground
      • Between DLC-2 terminal K and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between connector C-14 and connector C-71 because the wiring harness is shorted to ground.
No Go to the next step.
9 INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-71 AND REAR BODY CONTROL MODULE (RBCM)
  • Disconnect the rear body control module (RBCM).
  • Connect connector C-71.
  • Inspect for continuity at the following terminals:
    • Between DLC-2 terminal L and body ground
      • Between DLC-2 terminal K and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between the rear body control module (RBCM) and connector C-71 because the wiring harness is shorted to ground.
No Go to the next step.
10 INSPECT FOR SHORT TO GROUND BETWEEN BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH) AND REAR BODY CONTROL MODULE (RBCM)
  • Inspect for continuity at the following terminals:
    • Between rear body control module (RBCM) terminal 4L (wiring harness side) and body ground
      • Between rear body control module (RBCM) terminal 4I (wiring harness side) and body ground
  • Is there continuity?
 Yes Go to the next step.
No Replace the rear body control module (RBCM) because there is a short to ground in the rear body control module (RBCM).
(See REAR BODY CONTROL MODULE (RBCM) REMOVAL/INSTALLATION .)
11 INSPECT FOR SHORT TO GROUND BETWEEN BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH) AND CONNECTOR C-39
  • Disconnect connector C-39.
  • Inspect for continuity at the following terminals:
    • Between rear body control module (RBCM) terminal 4L (wiring harness side) and body ground
      • Between rear body control module (RBCM) terminal 4I (wiring harness side) and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between the rear body control module (RBCM) and connector C-39 because the wiring harness is shorted to ground.
No Go to the next step.
12 INSPECT CAN LINE IN BLIND SPOT MONITORING (BSM) CONTROL MODULE (LH) FOR SHORT TO GROUND
  • Disconnect the blind spot monitoring (BSM) control module (LH) connector.
  • Inspect for continuity at the following terminals:
    • Between blind spot monitoring (BSM) control module (LH) terminal C (wiring harness side) and body ground
      • Between blind spot monitoring (BSM) control module (LH) terminal D (wiring harness side) and body ground
  • Is there continuity?
 Yes Repair or replace the wiring harness between the blind spot monitoring (BSM) control module (LH) and connector C-39 because the wiring harness is shorted to ground.
No Replace the blind spot monitoring (BSM) control module (LH) because there is a short to ground in the blind spot monitoring (BSM) control module (LH).
(See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION .)
scientia non olet · About LEMON Manuals