Diagnostic procedure

NO. 1 ANY OF FOLLOWING LIGHTS DO NOT ILLUMINATE WITH IGNITION ON DIAGNOSTIC PROCEDURE

STEP	INSPECTION		ACTION
1	VERIFY WHERE MALFUNCTION IS IN WARNING LIGHTS AND INDICATOR LIGHTS' COMMON POWER SUPPLY, OR IN OTHER WARNING LIGHTS AND INDICATOR LIGHTS Connect the M-MDS (IDS) to the DLC-2. Turn on all warning lights and indicator lights using the instrument cluster PID WL+IL of active command modes. (See ACTIVE COMMAND MODES INSPECTION [INSTRUMENT CLUSTER] .) Do other warning and indicator lights illuminate?	Yes	Go to Step 5.
1		No	If communication error message is displayed on the M-MDS (IDS) screen: Go to the next step. If communication error message is not displayed: Replace the instrument cluster. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION .)
2	INSPECT INSTRUMENT CLUSTER POWER SUPPLY FUSE Inspect the instrument cluster ignition power supply fuse. Is the fuse normal?	Yes	Go to the next step.
2		No	Inspect the blown fuse's circuit for short to ground. Repair or replace the wiring harness for a possible short to ground as necessary. Install appropriate amperage fuse.
*3	VERIFY WHETHER MALFUNCTION IS IN WIRING HARNESS (BETWEEN INSTRUMENT CLUSTER POWER SUPPLY AND INSTRUMENT CLUSTER FOR CONTINUITY) OR ELSEWHERE Switch the ignition to ON. Measure the voltage at the instrument cluster terminal 2S (wiring harness-side). Is the voltage approx. 12 V?	Yes	Go to the next step.
*3		No	Inspect for open circuit between instrument cluster and ignition. Repair or replace the wiring harness for a possible open circuit as necessary.
*4	VERIFY WHETHER MALFUNCTION IS IN WIRING HARNESS (BETWEEN INSTRUMENT CLUSTER AND GROUND FOR CONTINUITY) OR INSTRUMENT CLUSTER Switch the ignition to off. Disconnect the instrument cluster connector. Inspect for continuity between instrument cluster terminal K (wiring harness-side) and body ground. Is there continuity?	Yes	Replace the instrument cluster. (Open circuit in the instrument cluster) (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION .)
*4		No	Repair or replace the wiring harness for a possible open circuit and poor contact in GND point.
5	CONFIRM DSC HU/CM DTC Retrieve the DSC HU/CM DTC using the M-MDS (IDS). (See DTC INSPECTION [DYNAMIC STABILITY CONTROL (DSC)] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [DYNAMIC STABILITY CONTROL (DSC)] .)
5		No	If communication error message is displayed on the M-MDS (IDS) screen: Go to the next step. If communication error message is not displayed: Go to Step 9.
6	INSPECT DSC HU/CM POWER SUPPLY FUSE Inspect the DSC HU/CM ignition power supply fuse. Is the fuse normal?	Yes	Go to the next step.
6		No	Inspect the blown fuse's circuit for short to ground. Repair or replace the wiring harness for a possible short to ground as necessary. Install appropriate amperage fuse.
*7	VERIFY WHETHER MALFUNCTION IS IN WIRING HARNESS (BETWEEN DSC HU/CM POWER SUPPLY AND DSC HU/CM FOR CONTINUITY) OR ELSEWHERE Switch the ignition to ON. Measure the voltage at the DSC HU/CM terminal Q (wiring harness-side). Is the voltage approx. 12 V?	Yes	Go to the next step.
*7		No	Inspect for open circuit between DSC HU/CM and ignition. Repair or replace the wiring harness for a possible open circuit as necessary.
*8	VERIFY WHETHER MALFUNCTION IS IN WIRING HARNESS (BETWEEN DSC HU/CM AND GROUND FOR CONTINUITY) OR ELSEWHERE Switch the ignition to off. Disconnect the DSC HU/CM connector. Inspect for continuity between DSC HU/CM terminal AL (wiring harness-side) and body ground. Is there continuity?	Yes	Replace the DSC HU/CM. (Open circuit in the DSC HU/CM) (See DSC HU/CM REMOVAL/INSTALLATION .)
*8		No	Repair or replace the wiring harness for a possible open circuit and poor contact in GND point.
9	CONFIRM INSTRUMENT CLUSTER DTC Retrieve the instrument cluster DTC using the M-MDS (IDS). (See DTC INSPECTION [INSTRUMENT CLUSTER] .) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [INSTRUMENT CLUSTER] .)
9		No	Replace the instrument cluster. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION .)

When performing an asterisked (*) troubleshooting inspection, shake the wiring harness and connectors while doing the inspection to discover whether poor contact points are the cause of any intermittent malfunctions. If there is a problem, check to make sure connectors, terminals and wiring harness are connected correctly and undamaged.