| 1 |
VERIFY PCM DTC
|
Yes |
Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-G 2.0]
.)
DTC troubleshooting completed, then go to the next step. |
| No |
Go to the next step. |
| 2 |
INSPECT BATTERY
|
Yes |
Charge or replace the battery, then go to Step 7.
(See BATTERY RECHARGING
.) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0]
.) |
| No |
Go to the next step. |
| 3 |
INSPECT GENERATOR
|
Yes |
Replace the generator, then go to Step 7.
(See GENERATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.0]
.) |
| No |
Go to the next step. |
| 4 |
INSPECT FUSE CONDITION
- Is the fuse (SRS1 7.5A, ABS/DSCS 30A, ABS/DSCM 50A) normal?
|
Yes |
Go to the next step. |
| No |
- If the fuse is blown:
- Refer to the wiring diagram and verify whether or not there is a common connector between fuse and DSC HU/CM terminal I, A and B.
If there is a common connector:
Go to Step 7. |
| 5 |
INSPECT DSC HU/CM POWER CIRCUIT FOR OPEN CIRCUIT
- Switch the ignition OFF.
- Disconnect the DSC HU/CM connector.
- Switch the ignition ON (engine off).
- Measure the voltage as followings:
- DSC HU/CM terminal I (wiring harness-side)-body ground
- DSC HU/CM terminal A (wiring harness-side)-body ground
- DSC HU/CM terminal B (wiring harness-side)-body ground
- Is the voltage 10 V or more?
|
Yes |
Go to the next Step. |
| No |
Refer to the wiring diagram and verify whether or not there is a common connector in the followings.
- Battery-DSC HU/CM terminal I
- Battery-DSC HU/CM terminal A
- Battery-DSC HU/CM terminal B
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has an open circuit.
Go to Step 7. |
| 6 |
INSPECT DSC HU/CM GROUND CIRCUIT FOR OPEN CIRCUIT OR POOR GROUND
- Switch the ignition OFF.
- Disconnect the DSC HU/CM connector.
- Measure the resistance between DSC HU/CM terminal AK (wiring harness-side) and body ground.
- Is the resistance 0-1 ohm?
|
Yes |
Go to the next step. |
| No |
- If the open circuit could be detected in the wiring harness:
- Refer to the wiring diagram and verify whether or not there is a common connector between DSC HU/CM terminal AK and body ground.
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has an open circuit.
- If the resistance is out of specification:
- Refer to the wiring diagram and verify whether or not there is a common connector between DSC HU/CM terminal AK and body ground.
If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a poor ground.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a poor ground.
|
| 7 |
VERIFY DTC TROUBLESHOOTING COMPLETED
|
Yes |
Repeat the inspection from Step1 If the malfunction recurs, replace the DSC HU/CM, then go to the next step.
(See DSC HU/CM REMOVAL/INSTALLATION
.) |
| No |
Go to the next step. |
| 8 |
VERIFY NO DTC IS PRESENT
|
Yes |
Go to the applicable DTC inspection.
(See DTC TABLE [DSC HU/CM] .) |
| No |
DTC troubleshooting completed. |