LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2012 >> 6 i Touring >> Repair and Diagnosis >> External Pages >> Different car >> Section 623 (On-Board Diagnostic [Restraints System)) >> PID/Data Monitor Table

PID/Data Monitor Table

WARNING: This page is about a different car, the 2009 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
PID name (definition) Unit/Operation Operation Status (Reference) Terminal
BUCKLE_D (Driver-side buckle switch status) Buckled/Unbuckled
  • Driver-side front seat belt fastened (Driver-side buckle switch off): Buckled
  • Driver-side front seat belt not fastened (Driver-side buckle switch on): Unbuckled
 2M
BUCKLE_P (Passenger-side buckle switch status) Buckled/Unbuckled Occupant seated in passenger-side front seat. On
  • Passenger-side front seat belt fastened (Passenger-side buckle switch off): Buckled
  • Passenger-side front seat belt not fastened (Passenger-side buckle switch on): Unbuckled
 2O
DTC_CLR_ST (Seat weight sensor DTC cleared status) Started/Normal End/In Process OCS Fault information cleared at seat weight sensor 2N
OCS_SYS_ST (Seat weight sensor status) Empty/SMALL/LARGE/Indeterminate/Invalid Occupant classification status determined by seat weight sensor 2N
OCS_CAL_ST (Seat weight sensor calibration status) Starting/Normal End/Commanding/NG (Voltage)/NG (Weight)/In Process Timeout/OCS Fault
  • Seat weight sensor calibration start-up Starting
  • Seat weight sensor calibration completed normally Normal End
  • Seat weight sensor calibration command being sent Commanding
  • Voltage malfunction during seat weight sensor calibration NG (Voltage)
  • Weight error during seat weight sensor calibration NG (Weight)
  • Seat weight sensor calibration time limit passed Timeout
  • Seat weight sensor calibration being processed: In Process
  • Seat weight sensor or Seat weight sensor control module malfunction OCS Fault
 2N
RES_AB_D (Driver-side air bag module (inflator No. 1) resistance nominal) ohm Continuous 1.5-4.1 ohm 3E, 3G
RES_AB_P (Passenger-side air bag module (inflator No 1) resistance nominal) ohm Continuous 1 5-4 1 ohm 3I, 3K
RES_AB2_D (Driver-side air bag module (inflator No 2) resistance nominal) ohm Continuous. 1 5-4.1 ohm 3M, 3O
RES_AB2_P (Passenger-side air bag module (inflator No 2) resistance nominal) ohm Continuous 1 5-4 1 ohm 3P, 3N
RES_CAB_D (Driver-side curtain air bag module resistance nominal) ohm Continuous 1 5-4 1 ohm 1I, 1K
RES_CAB_P (Passenger-side curtain air bag module resistance nominal) ohm Continuous. 1 5-4 1 ohm 1M, 1O
RES_PT_D (Driver-side pretensioner seat belt resistance nominal) ohm Continuous 1 5-4 1 ohm 2A, 2C
RES_PT_P (Passenger-side pretensioner seat belt resistance nominal) ohm Continuous 1 5-4 1 ohm 2E, 2G
RES_SAB_D (Driver-side side air bag module resistance nominal) ohm Continuous 1 5-4 1 ohm 1A, 1C
RES_SAB_P (Passenger-side side air bag module resistance nominal) ohm Continuous 1 5-4 1 ohm 1E, 1G
PS_WEIGHT (Seat weight sensor measured weight of passenger) kg Display of load (body weight) on passenger-side seat 2N
TRAK_SW (Seat track position sensor state) Forward/Rearward
  • Front seat front position. Forward
  • Front seat rear position Rearward
 2J, 2L
TRAK_SW_FLT (Seat track position sensor malfunction status) O.K./Fault
  • Seat track position sensor normal. O.K.
  • Seat track position sensor abnormal Fault
 2J, 2L
VPWR (SAS control module power voltage) V Switch the ignition to ON B+ 3A
scientia non olet · About LEMON Manuals