Engine Mount Installation Note

WARNING: This page is about a different car, the 2009 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.

Tighten the No. 3 engine mount stud bolts.
NOTE:
- If the No. 3 engine mount bracket and the engine are removed, retighten the No. 3 engine mount stud bolts
Tightening torque

16-23 N.m {1.7-2.3 kgf.m, 12-16 ft.lbf}

Fig 1: Identifying No. 3 Engine Mount Stud Bolts
Courtesy of MAZDA MOTORS CORP.
Secure the engine and the transaxle using an engine jack and attachment as shown.
NOTE:
- Temporarily bolt 1 approximately three thread.
  
  Fig 2: Securing Engine & Transaxle Using Engine Jack & Attachment
  Courtesy of MAZDA MOTORS CORP.
Temporarily tighten the No. 4 engine mount bracket bolt and nuts in the order shown in the figure.

Fig 3: Identifying No. 4 Engine Mount, Bracket & Bolts
Courtesy of MAZDA MOTORS CORP.

Tighten the No. 4 engine mount bracket in the order shown in the figure.

Fig 4: Identifying No. 4 Engine Mount Bracket Tightening Sequence

Courtesy of MAZDA MOTORS CORP.

TIGHTENING TORQUE

Installation Position	Tightening Torque
1, 2, 3	67-93 N.m {6.9-9.4 kgf.m, 50-68 ft.lbf}
4	86-116 N.m {8.8-11 kgf.m, 64-85 ft.lbf}

Temporarily tighten the No. 3 engine mount bracket bolt and nuts in the order shown in the figure.

Fig 5: Identifying No. 3 Engine Mount Bracket Bolt & Nut Temporary Tightening Sequence
Courtesy of MAZDA MOTORS CORP.

Tighten the No. 3 engine mount bracket in the order shown in the figure.

TIGHTENING TORQUE

Installation Position	Tightening Torque
1	75-104 N.m {7.7-10 kgf.m, 56-76 ft.lbf}
2, 3, 4, 5	54-71 N.m {5.6-7.2 kgf.m, 40-52 ft.lbf}

Fig 6: Identifying No. 3 Engine Mount Bracket Tightening Sequence

Courtesy of MAZDA MOTORS CORP.

Install the No. 1 engine mount, No. 1 engine mount bracket and the front crossmember as a single unit. (See FRONT CROSSMEMBER REMOVAL/INSTALLATION [MZI-3.7] .)

Fig 7: Identifying No. 1 Engine Mount

Courtesy of MAZDA MOTORS CORP.

Install the through bolt A on the front crossmember side until approximately three pitches are showing.

Fig 8: Identifying No. 1 Engine Mount Bracket Bolts

Courtesy of MAZDA MOTORS CORP.

Temporarily tighten the No. 1 engine mount bracket bolts in the order of B and C.
Tighten the No. 1 engine mount bracket bolts in the order of B and C.
Tightening torque

77-103 N.m {7.9-10 kgf.m, 57-75 ft.lbf}

Fig 9: Identifying No. 1 Engine Mount Bracket Bolts
Courtesy of MAZDA MOTORS CORP.
Tighten the No. 1 engine mount bolt D.
Tightening torque

77-103 N.m {7.9-10 kgf.m, 57-75 ft.lbf}

Fig 10: Identifying No. 1 Engine Mount Bolt D

Courtesy of MAZDA MOTORS CORP.

Tighten the bolt A.
Tightening torque

94-116 N.m {9.6-11 kgf.m, 70-85 ft.lbf}
Install the intermediate shaft bolt, and disconnect the steering shaft. (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION [WITHOUT ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .) (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION [WITH ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
Install the transverse member. (See TRANSVERSE MEMBER REMOVAL/INSTALLATION .)