Diagnostic Procedure

WARNING: This page is about a different car, the 2009 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.

DIAGNOSTIC PROCEDURE

Step	Inspection		Action
1	PERFORM DTC INSPECTION Clear the DTC from the keyless control module and PCM memory using the M-MDS. See CLEARING DTC [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] . Perform the immobilizer system (advanced keyless entry and push button start system) DTC inspection using the M-MDS. See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] . Is the following DTC present? Instrument cluster: B10D7:05 PCM: P1260:00	Yes	Perform the security light-13, DTC: B10D7:05/P1260:00 inspection. See SECURITY LIGHT: 13, DTC: B10D7:05/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] .
1		No	Go to the next step
2	VERIFY THAT THERE IS A VALID KEY Are there any valid keys which can start the engine other than the cause of the displayed DTC?	Yes	Go to the next step.
2		No	Program an additional key referring to the immobilizer system-related parts programming, then go to the next step See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .
3	PERFORM DTC INSPECTION Switch the ignition to ON using the valid key other than the cause of the displayed DTC (engine off). Clear the DTC from the keyless control module and PCM memory using the M-MDS See CLEARING DTC [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] . Perform the immobilizer system (advanced keyless entry and push button start system) DTC inspection using the M-MDS. See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] . Is the same DTC present?	Yes	Replace the coil antenna, then go to the next step See COIL ANTENNA REMOVAL/INSTALLATION [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .
3		No	Dispose of the malfunctioning key and program a new key if necessary, then go to Step 6 See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .
4	PERFORM DTC INSPECTION Clear the DTC from the keyless control module and PCM memory using the M-MDS See CLEARING DTC [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] . Perform the immobilizer system (advanced keyless entry and push button start system) DTC inspection using the M-MDS. See DTC INSPECTION [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] . Is the same DTC present?	Yes	Replace the PCM and program the immobilizer system-related parts, then go to the next step. See PCM REMOVAL/INSTALLATION [L5] . See PCM REMOVAL/INSTALLATION [MZI-3.7] . See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .
4		No	Go to Step 6.
5	VERIFY TROUBLESHOOTING COMPLETED Clear the DTC from the keyless control module and PCM memory using the M-MDS. See CLEARING DTC [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] . Perform the immobilizer system (advanced keyless entry and push button start system) DTC inspection using the M-MDS See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] . Is the same DTC present?	Yes	Replace the keyless control module and program the immobilizer system-related parts, then go to the next step See KEYLESS CONTROL MODULE REMOVAL/INSTALLATION [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] . See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .
5		No	Go to the next step.
6	VERIFY THAT NO OTHER DTCs ARE PRESENT Are any DTCs present?	Yes	Go to the applicable DTC inspection See DTC TABLE [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] )
6		No	DTC troubleshooting completed.