LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2007 >> B4000 SE, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 70 (Engine Controls - Self-Diagnostics) >> Diagnostic Tests >> DTC P0455, DTC P0456 Or DTC P1443 >> Diagnostic Procedures

Diagnostic Procedures

WARNING: This page is about a different car, the 2003 Mazda B4000, 2003 Mazda B3000, and 2003 Mazda B2300. However, it is still accessible from the selected car via links, so may be relevant.
  1. If QUICK TEST was not performed, go to QUICK TEST  under SELF-DIAGNOSTIC SYSTEM. If QUICK TEST was performed:
    • For DTC P0455, go to next step.
    • For DTC P1443, go to step  3 .
  2. Visually Check For Large EVAP System Leak -  Verify fuel cap is installed. DO NOT tighten cap or check for correct installation at this time. Verify both input port vacuum hose and EVAP return hose are attached to EVAP canister purge valve. Verify Canister Vent (CV) solenoid is properly attached to EVAP canister. Visually inspect fuel vapor hoses for disconnected, cracked or loose connections to intake manifold and the following locations:
    • EVAP canister purge valve.
    • EVAP canister.
    • Fuel vapor vent valve assembly.
    Check for damage to fuel filler pipe and fuel tank. If a problem is found, repair or install a new component as necessary. After repair, go to step  7 . If a problem is not found, go to next step.
  3. Check For EVAP System Leaks -  Disconnect EVAP return hose from intake manifold and plug EVAP return hose. Connect EVAP System Leak Tester to EVAP test port. Perform EVAP System Leak Test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST under SYSTEM TESTS (EVAPORATIVE EMISSION) in SYSTEM & COMPONENT TESTING - B2300, B3000, B4000 & TRIBUTE article. If pressure stays above 8 in. H2O (1.99 kPa), go to next step. If pressure does not stay above 8 in. H2O (1.99 kPa), verify fuel filler cap is properly installed. Repair or install new components as necessary. After repair, go to step  7 .
  4. Check For Blockage Between EVAP Canister Purge Valve & Fuel Vapor Tee -  With KOEO, using scan tool, select DIAGNOSTIC DATA LINK. Select PCM. Select ACTIVE COMMAND MODES. Select OUTPUT TEST MODE. Close EVAP CV solenoid using EVAPCV PID. Pressurize EVAP system to 14 in. H2O (3.48 kPa). Press STOP (#4) to open CV solenoid. Observe pressure. If pressure drops immediately, go to next step. If pressure does not drop immediately, install a new vapor line between EVAP canister purge valve and fuel vapor tee. After repair, go to step  8 .
  5. Check For Blockage Between Fuel Filler Pipe & Fuel Vapor Tee -  Connect EVAP System Leak Tester to fuel filler pipe. Using scan tool, select DIAGNOSTIC DATA LINK. Select PCM. Select ACTIVE COMMAND MODES. Select OUTPUT TEST MODE. Close EVAP CV solenoid using EVAPCV PID. Pressurize EVAP system to 14 in. H2O (3.48 kPa). Press STOP (#4) to open CV solenoid. Observe pressure. If pressure drops immediately, go to next step. If pressure does not drop immediately, install NEW fuel tank vapor line(s). Repeat this test step to verify repair. After repair, go to step  8 .
  6. Check For Failed EVAP Canister Purge Valve Or Fuel Tank Pressure Sensor -  If both DTC P0455 and P1443 were set at step  1 , install a NEW EVAP canister purge valve. After repair, go to next step. If both DTC P0455 and P1443 were not set at step  1 , install a NEW FTP sensor. After repair, go to next step.
  7. EVAP System Leak Test -  Connect all disconnected connectors and hoses. Perform EVAP System Leak Test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST under SYSTEM TESTS (EVAPORATIVE EMISSION) in SYSTEM & COMPONENT TESTING - B2300, B3000, B4000 & TRIBUTE article. If EVAP System Leak Test passes, go to step  9 to verify repair. If EVAP System Leak Test does not pass, locate and repair leak. Repeat this step.
  8. Drive Cycle -  Reconnect all connectors. Using scan tool, clear DTC from PCM memory. Perform EVAP RUNNING LOSS SYSTEM REPAIR VERIFICATION DRIVE CYCLE  in MONITOR REPAIR VERIFICATION DRIVE CYCLES under DRIVE CYCLE PROCEDURES. Using scan tool, retrieve DTCs. If same DTC is not present, go to next step. If same DTC is present, replace faulty PCM. After repair, go to next step.
  9. Verify Trouble Shooting Of DTCs Completed -  Perform QUICK TEST  under SELF-DIAGNOSTIC SYSTEM. If any DTC is present, go to applicable procedure for other DTCs. See DIAGNOSTIC TROUBLE CODE DEFINITIONS  . If no DTC is present, trouble shooting is complete.
scientia non olet · About LEMON Manuals