LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2002 >> Tribute LX, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 69 (Engine Controls - Self-Diagnostics) >> Diagnostic Tests >> DTC P1131, DTC P1151, DTC P2195, DTC P2196, DTC P2197 Or DTC P2198 >> Diagnostic Procedures

Diagnostic Procedures

WARNING: This page is about a different car, the 2003 Mazda Tribute. However, it is still accessible from the selected car via links, so may be relevant.
  1. If QUICK TEST was not performed, go to QUICK TEST  under SELF-DIAGNOSTIC SYSTEM. If QUICK TEST was performed, go to next step.
  2. DTCS P1131, P1151, P2195, P2196, P2197, P2198: Upstream HO2S(s) Not Switching -  Check air intake system for leaks and damage. Verify integrity of PCV system. See POSITIVE CRANKCASE VENTILATION SYSTEM  testing under SYSTEM TESTS. Check for vacuum leaks. If any problems are present, repair as necessary. After repair, go to step  21. If problems are not present, go to next step.
  3. Perform KOER Self-Test -  Disconnect fuel vapor hose from intake manifold and plug fitting at intake manifold. Start engine and run at 2000 RPM for 5 minutes and return to idle. Perform KOER self-test. If DTC P1131, P1151, P2195, P2196, P2197 and/or P2198 are present, go to next step. If no DTCs are present, perform EVAP Emissions System Leak Test to locate leak. Refer to EVAPORATIVE EMISSIONS SYSTEM LEAK TEST under FUEL EVAPORATIVE SYSTEM under EMISSION SYSTEMS & SUB-SYSTEMS in SYSTEM & COMPONENT TESTING - B2300, B3000, B4000 & TRIBUTE article.
    4. NOTE: If a spark occurs, indicating a short, remove fused jumper wire and check for short to ground (check fuse in heater circuit).
  4. HO2S Circuit Test (With Lean DTCs) -  Turn ignition off. Disconnect suspect HO2S 4-pin harness connector related to DTC.
    • DTC P1131, P2195, P2196: HO2S11 (Front Bank 1).
    • DTC P1151, P2197, P2198: HO2S21 (Front Bank 2).

    Turn ignition on, engine off. Using scan tool, select DIAGNOSTIC DATA LINK. Select PCM. Select PIN/DATA MONITOR AND RECORD. Access O2S11 (Front Bank 1) or O2S21 (Front Bank 2) PID. Connect fused jumper wire between HO2S SIG and HO2S VPWR at HO2S 4-pin harness connector. See Figure. If voltage reading is 1.3 volts or more, go to next step. If voltage reading is not as specified, short or open circuit is present. Go to step  7.

  5. Check Signal Return Circuit For Shorts And Opens -  Measure resistance of HO2S SIG RTN circuit (Orange wire) between HO2S 4-pin harness connector and battery ground terminal. If resistance reading is less than 5 ohms, reconnect all connectors and go to step  10. If resistance reading is not as specified, repair open circuit in Orange wire or short to ground between PCM 104-pin harness connector terminal No. 91 and HO2S 4-pin harness connector. After repair, go to next step.
  6. Check HO2S Signal Return Circuit In Vehicle Harness -  Disconnect PCM 104-pin harness connector. Connect Breakout Box (49-UN01-130) to PCM harness connector only. See Figure. Measure resistance of HO2S SIG RTN circuit between breakout box terminal No. 91 and HO2S 4-pin harness connector (Orange wire). If resistance reading is less than 5 ohms, replace PCM. After repair, go to step  21. If resistance reading is not as specified, repair open circuit in Orange wire between PCM 104-pin harness connector terminal No. 91 and HO2S 4-pin harness connector. After repair, go to step  21.
  7. Check Resistance Of HO2S Ground Circuits -  Disconnect PCM 104-pin harness connector. Connect Breakout Box (49-UN01-130) to PCM harness connector only. See Figure. Measure resistance of HO2S SIG circuit between following breakout box terminal and appropriate HO2S 4-pin harness connector terminal:
    • HO2S-11 SIG: Breakout box terminal No. 60.
    • HO2S-21 SIG: Breakout box terminal No. 87.
    If resistance reading is less than 5 ohms, go to next step. If resistance reading is not as specified, repair open circuit. See appropriate WIRING DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. After repair, go to step  21.
  8. Check HO2S Circuit Wiring Harness For Short To Ground -  Measure resistance of HO2S SIG circuit between breakout box terminals No. 60 or 87 and terminal No. 103 (PWR GND). Measure resistance of HO2S SIG circuit between breakout box terminal No. 60 or 87 and terminal No. 91 (SIG RTN). If each resistance reading is more than 10,000 ohms, go to next step. If each resistance reading is not as specified, repair short circuit in suspect wire or replace harness. After repair, go to step  21.
  9. Check HO2S For Short To Ground -  Reconnect HO2S connector. Measure resistance of HO2S SIG circuit between appropriate breakout box terminal No. 60 (HO2S11 circuit) or No. 87 (HO2S21 circuit) and breakout box terminal No. 103 (PWR GND circuit). Record reading. Measure resistance of appropriate HO2S SIG circuit between breakout box terminal No. 60 (HO2S11 circuit) or No. 87 (HO2S21 circuit) and breakout box terminal No. 91 (SIG RTN circuit). Record reading. If resistance reading is more than 10,000 ohms, replace PCM. After repair, go to step  21. If resistance reading is not as specified, replace HO2S. After repair, go to step  21.
  10. Check HO2S Ability To Generate A Voltage Greater Than 0.5 Volt -  Inspect HO2S harness for chafing, burned wiring or other damage. Repair as necessary. Disconnect suspect HO2S 4-pin harness connector. Connect a DVOM between HO2S connector (component side) SIG terminal and SIG RTN terminal or GND terminal. See Figure. Run engine at 2000 RPM for 3 minutes. Run KOER Self-Test and monitor HO2S voltage. Observe voltage. Turn ignition off. If voltage is more than 0.5 volt during or at end of self-test, go to next step. If voltage reading is more than 0.5 volt during or at end of Self-Test, go to next step. If voltage reading is not as specified, replace HO2S. After repair, go to step  21.
  11. Monitor HO2S (PID) For Proper Switching -  Start engine. Warm up engine to operating temperature. Using scan tool, select DIAGNOSTIC DATA LINK. Select PCM. Select PID/DATA MONITOR AND RECORD. Access O2S11 (Front Bank 1) or O2S21 (Front Bank 2) PID and monitor while wiggling, bending and shaking small sections of engine harness from HO2S to PCM. Turn ignition off. If HO2S voltage reading did not stay high (more than 0.45 volt) or low (less than 0.45 volt), go to next step. If HO2S voltage reading stayed high or low, isolate cause for lack of HO2S switching and repair as necessary. After repair, go to step  21.
    WARNING: Fuel system is pressurized when engine is not running. To prevent injury or fire, use caution when working on fuel system.
    12. NOTE: During next step, fuel pump will only operate for about 8 seconds when Output Test Mode is selected and activated.
  12. Check Fuel Pressure -  Install fuel pressure gauge. Turn ignition on, engine off. Using scan tool, select DIAGNOSTIC DATA LINK. Select PCM. Select ACTIVE COMMAND MODES. Access OUTPUT TEST MODE and run fuel pump to obtain maximum fuel pressure. If fuel pressure is 55-70 psi (380-482 kPa), go to next step. If fuel pressure is not as specified, refer to FUEL DELIVERY SYSTEM  testing under SYSTEM TESTS.
  13. Check Injector Fault PIDs -  Access INJ1F-INJ6F PIDs. If an injector(s) fault is present, go to next step. If an injector fault is not present, go to step  17.
    14. NOTE: Performing following procedure erases Continuous Memory DTCs.
    NOTE: Use injector fault PID to determine fuel injector circuit(s) requiring testing.
  14. Check Fuel Injector(s) & Harness Resistance -  Disconnect PCM 104-pin harness connector. Connect Breakout Box (49-UN01-130) to PCM harness connector only. See Figure. Measure resistance of suspect fuel injector between suspect INJ circuit breakout box terminal and breakout box terminal No. 71 (VPWR). See Figure. If resistance reading is 11-18 ohms, replace PCM. After repair, go to step  21. If resistance reading is not within specification, go to next step.
  15. Check Fuel Injector Harness Resistance -  Disconnect fuel injector 2-pin harness connector at suspect fuel injector. Measure resistance of VPWR circuit (Red wire) between breakout box terminal No. 71 and fuel injector harness connector. Measure resistance of INJ circuit between appropriate breakout box terminal and fuel injector harness connector. See Figure. If each resistance reading is less than 5 ohms, go to next step. If each resistance reading is not as specified, repair open circuit in Red wire between suspect fuel injector harness connector and PCM 104-pin harness connector terminal No. 71. See appropriate WIRING DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. After repair, go to step  21.
  16. Check Fuel Injector Harness Circuit For Short To Power & Ground -  Measure resistance between suspect INJ circuit harness connector and breakout box terminals No. 71 (VPWR) and 103 (PWR GND). If each resistance reading is more than 10,000 ohms, go to next step. If each resistance reading is not as specified, repair short circuit. After repair, go to step  21.
  17. Flow Test Fuel Injector(s) -  Using a fuel injector tester, flow test fuel injectors following equipment manufacturers instructions. Flow rate should be 17 lb/hr (7.8 kg/hr) for 2.0L engines and 22 lb/hr (10.1 kg/hr) for 3.0L engines. If leakage and flow are within specification, go to next step. If leakage and flow are not within specification, replace faulty fuel injector(s). After repair, go to step  21.
  18. Inspect Induction System For Air Leaks -  Inspect following areas for signs of air leaks:
    • Inlet tube(s) from air cleaner to throttle body.
    • Gaskets which seal upper and lower intake manifold.
    • Vacuum hoses and lines for cracks and proper connections.
    • PCV system.
    If there are no signs of leakage or damage, go to next step. If there are any signs of leaks or damage, repair as necessary. After repair, go to step  21.
    19. NOTE: Use Misfire DTCs (if present) to determine which cylinder's compression to check. Otherwise check all cylinders.
  19. Check Cylinder Compression -  Check cylinder compression. Refer to MECHANICAL INSPECTION under PRELIMINARY INSPECTION & ADJUSTMENTS in BASIC DIAGNOSTIC PROCEDURES article. If cylinder compression readings are within specification, go to next step. If cylinder compression readings are not within specification, repair as necessary. After repair, go to step  21.
  20. Test Drive While Monitoring HO2S PID For Proper Switching -  Using scan tool, select DIAGNOSTIC DATA LINK. Select PCM. Select PID/DATA MONITOR AND RECORD. Access O2S11 (Front Bank 1) or O2S21 (Front Bank 2) PID. While observer views PID, test drive vehicle under different road conditions in an attempt to simulate original fault. If HO2S appears to switch properly, unable to duplicate problem. Go to next step. If HO2S does not appear to switch properly, replace faulty HO2S. After repair, go to next step.
  21. Verify Trouble Shooting Of DTCs Completed -  Reconnect all disconnected connectors. Clear DTCs from PCM memory using scan tool. Perform QUICK TEST  under SELF-DIAGNOSTIC SYSTEM. If same DTC is present, replace faulty PCM. Repeat QUICK TEST  under SELF-DIAGNOSTIC SYSTEM. If same DTC is not present, go to applicable procedure for other DTCs. See DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no DTCs are present, trouble shooting is complete.
scientia non olet · About LEMON Manuals