LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2002 >> Tribute LX, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 60 (Engine Controls [Self-Diagnostics 2.3L]) >> Diagnostic Tests >> DTC P0137: Rear Ho2S Circuit - Low Input >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2003 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
  1. If FREEZE FRAME DATA has been recorded, go to next step. If FREEZE FRAME DATA has not been recorded, record FREEZE FRAME DATA. Go to next step.
  2. Verify Related Repair Information Availability -  Check for related Service Bulletins and/or on-line repair information availability. If any related repair information is available, perform repair or diagnosis according to available repair information. If vehicle is not repaired, go to next step. If related repair information is not available, go to next step.
  3. Verify Related Pending Or Stored DTCs -  Turn ignition off, then on (engine off). Verify pending code or stored DTCs using WDS or equivalent. If other DTC is present, go to appropriate DTC trouble shooting procedures. Refer to DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no other DTCs are present, go to next step.
  4. Identify Trigger DTC For FREEZE FRAME DATA -  If DTC P0137 is present on FREEZE FRAME DATA, go to next step. If any other DTC triggered FREEZE FRAME DATA, diagnose that DTC first. Refer to DIAGNOSTIC TROUBLE CODE DEFINITIONS .
  5. Inspect Rear HO2S Connector For Poor Connection -  Turn ignition off. Disconnect rear HO2S 4-pin harness connector. Inspect for poor connection (such as damaged, pulled-out terminals, corrosion). If malfunction is not present, go to next step. If any malfunctions are present, repair terminal. After repair, go to step  11.
  6. Inspect PCM Connector For Poor Connection -  Disconnect PCM connectors. Check for poor connection (such as damaged, pulled-out terminals, corrosion). If malfunctions are not present, go to next step. If any malfunctions are present, repair terminal. After repair, go to step  11.
  7. Inspect Rear HO2S Signal Circuit For Open -  Inspect continuity between rear HO2S 4-pin harness connector terminal "A" and PCM 30-pin harness connector terminal "1Y" (White/Blue wire). See Fig 1. If continuity is present, go to next step. If continuity is not present, repair or replace harness for open circuit in White/Blue wire between rear HO2S 4-pin harness connector terminal "A" and PCM 30-pin harness connector terminal "1Y". See ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS article in ELECTRICAL. After repair, go to step  11.
    Fig 1: Identifying Rear HO2S Circuits & Harness Connector Terminals
    G00221501Courtesy of MAZDA MOTORS CORP.
  8. Inspect Rear HO2S Signal Circuit For Short To Ground Circuit -  Inspect continuity between rear HO2S 4-pin harness connector terminal "A" (White/Blue wire) and body ground. If continuity is present, repair short to power supply circuit in White/Blue wire between rear HO2S 4-pin harness connector terminal "A" and PCM 30-pin harness connector terminal "1Y". After repair, go to step  11.
  9. Inspect Rear HO2S Ground Circuit For Open -  Check continuity between rear HO2S 4-pin harness connector terminal "B" and PCM 30-pin harness connector terminal "2H" (Brown wire). If continuity is present, go to next step. If continuity is not present, repair open circuit in Brown wire between rear HO2S 4-pin harness connector terminal "B" and PCM 30-pin harness connector terminal "2H". After repair, go to step  11.
  10. Verify Current Input Signal Status -  Start engine. Access O2S12 PID using WDS or equivalent. Verify PID while racing engine at least 10 times (in NEUTRAL (MTX) or PARK (ATX)). If PID reading stays at more than 0.45 volt, repair or replace HO2S (rear). After repair, go to next step. If PID reading does not stay at more than 0.45 volt, go to next step.
  11. Verify Trouble Shooting Of DTC P0137 Is Completed -  Make sure to reconnect all disconnected connectors. Turn ignition on, engine off. Clear DTC from PCM memory using WDS or equivalent. Perform MODE 1 - PCM ADAPTIVE MEMORY PRODUCE DRIVE MODE  and MODE 3 - HO2S HEATER, HO2S & TWC REPAIR VERIFICATION DRIVE MODE  under DRIVE CYCLES. If PENDING CODE of same DTC is not present, go to next step. If PENDING CODE of same DTC is present, replace PCM. For PCM removal and installation, see POWERTRAIN CONTROL MODULE under COMPUTERIZED ENGINE CONTROLS in REMOVAL & INSTALLATION article. After repair, go to next step.
  12. Verify After Repair Procedure -  Using scan tool, perform After Repair Procedure. See AFTER REPAIR PROCEDURE . If any DTCs are present, go to appropriate DTC inspection. Refer to DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no DTCs are present, trouble shooting is complete.
scientia non olet · About LEMON Manuals