Diagnostic procedure

WARNING: This page is about a different car, the 2005 Mazda MX-5 Miata. However, it is still accessible from the selected car via links, so may be relevant.

DTC P0107 [BP, BP WITH TC] DIAGNOSTIC PROCEDURE

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDED Has FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
1		No	Record FREEZE FRAME DATA on repair order, then go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Check for related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY CURRENT SIGNAL STATUS: IS CONCERN INTERMITTENT OR CONSTANT? Connect the WDS or equivalent to the DLC-2. Clear the DTC from the PCM memory using the WDS or equivalent. Run the vehicle under the FREEZE FRAME DATA stored condition. Is the same DTC present?	Yes	Go to the next step.
3		No	Intermittent concern exists. Perform the "INTERMITTENT CONCERNS TROUBLESHOOTING". (See INTERMITTENT CONCERN TROUBLESHOOTING .)
4	INSPECT EGR BOOST SENSOR (BP), BARO/MAP SENSOR (BP WITH TC) CONNECTOR FOR POOR CONNECTION Turn the ignition switch off. Disconnect the EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC) connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 11.
4		No	Go to the next step.
5	CHECK POWER SUPPLY CIRCUIT VOLTAGE AT EGR BOOST SENSOR (BP), BARO/MAP SENSOR (BP WITH TC) CONNECTOR Turn the ignition switch to the ON position (Engine off). Measure voltage between EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC) terminal C (harness-side) and body ground. Is voltage within 4.5-5.5 V?	Yes	Go to the next step.
5		No	Repair or replace the wiring harness for a possible open circuit, then go to Step 11.
6	INSPECT EGR BOOST SENSOR (BP), BARO/MAP SENSOR (BP WITH TC) Inspect the EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC). (See EGR BOOST SENSOR (BP), BAROMETRIC PRESSURE (BARO)/MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR (BP WITH TC) INSPECTION [BP, BP WITH TC] .) Is there any malfunction?	Yes	Replace the EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC), then go to Step 11.
6		No	Go to the next step.
7	INSPECT PCM CONNECTOR FOR POOR CONNECTION Turn the ignition switch off. Disconnect the PCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 11.
7		No	Go to the next step.
8	INSPECT EGR BOOST SENSOR (BP), BARO/MAP SENSOR (BP WITH TC) SIGNAL CIRCUIT FOR SHORT TO GROUND Turn the ignition switch off. Inspect for continuity between following terminals: between EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC) terminal B (wiring harness-side) and body ground between EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC) terminal C (wiring harness-side) and body ground Is there continuity?	Yes	Repair or replace the wiring harness for a possible short to ground, then go to Step 11.
8		No	Go to the next step.
9	INSPECT EGR BOOST SENSOR (BP), BARO/MAP SENSOR (BP WITH TC) SIGNAL AND GROUND CIRCUIT FOR SHORT EACH OTHER Check continuity between EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC) terminal B and A (harness-side). Is there continuity?	Yes	Repair or replace suspected harness, then go to Step 11.
9		No	Go to the next step.
10	INSPECT EGR BOOST SENSOR (BP), BARO/MAP SENSOR (BP WITH TC) SIGNAL CIRCUIT FOR OPEN CIRCUIT Turn the ignition switch off. Inspect for continuity between the EGR boost sensor (BP), BARO/MAP sensor (BP WITH TC) terminal B and PCM terminal 4AE Is there continuity?	Yes	Go to the next step.
10		No	Repair or replace the wiring harness for a possible open circuit, then go to Step 11.
11	VERIFY TROUBLESHOOTING OF DTC P0107 COMPLETED Make sure to connect all disconnected connectors. Turn the ignition switch to the ON position (Engine off). Clear the DTC from the PCM memory using the WDS or equivalent. Start engine. Is same DTC present?	Yes	Replace PCM, then go to the next step.
11		No	Go to the next step.
12	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE ". (See AFTER REPAIR PROCEDURE .) Is any DTC present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE .)
12		No	Troubleshooting completed.