LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2002 >> Tribute LX, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 333 (On-Board Diagnostic (Engine Control System (L3)) >> DTC P2102 >> Diagnostic procedure

Diagnostic procedure

WARNING: This page is about a different car, the 2005 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
DTC P2102 [L3] DIAGNOSTIC PROCEDURE

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA HAS BEEN RECORDED 
  • Has FREEZE FRAME DATA been recorded?
 Yes Go to the next step.
No Record FREEZE FRAME DATA on repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Check for related Service Bulletins and/or online repair information availability.
  • Is any related repair information available?
 Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING CODE AND STORED DTCS 
  • Turn ignition switch to OFF, then ON (Engine off).
  • Verify pending and/or stored DTCs using the WDS or equivalent.
  • Is the DTC P2100 also present?
 Yes Go to appropriate DTC troubleshooting procedure, then go to Step 10.
No Go to the next step.
4 INSPECT THROTTLE BODY CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect throttle body connector.
  • Inspect for poor connection (such as damaged, pulled-put pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the terminal, then go to Step 10.
No Go to the next step.
5 INSPECT POWER SUPPLY CIRCUIT OF THROTTLE ACTUATOR FOR OPEN CIRCUIT 
  • Turn ignition switch to ON (Engine off).
  • Measure voltage between throttle body terminal F (harness-side) and body ground.
  • Is voltage B+  ?
 Yes Go to the next step.
No Repair or replace harness for open circuit, then go to Step 10.
6 INSPECT POWER SUPPLY CIRCUIT OF THROTTLE ACTUATOR FOR SHORT TO GROUND 
  • Turn the ignition switch off.
  • Check continuity between throttle body terminal F (harness-side) and body ground.
  • Is there continuity?
 Yes Repair or replace harness for short to ground circuit, then go to Step 10.
No Go to the next step.
7 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the terminal, then go to Step 10.
No Go to the next step.
8 INSPECT CONTROL CIRCUIT OF THROTTLE ACTUATOR FOR OPEN CIRCUIT 
  • Turn the ignition switch off.
  • Check continuity between throttle body terminal E (harness-side) and PCM terminal 88(1), 4AB(2) (harness-side).
  • Is there continuity?
 Yes Repair or replace harness for open circuit, then go to Step 10.
No Go to the next step.
9 INSPECT THROTTLE ACTUATOR 
 Yes Go to the next step.
No Replace throttle body, then go to the next step.
10 VERIFY TROUBLESHOOTING OF DTC P2102 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Turn ignition switch to ON (Engine off).
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Start engine and warm it up completely.
  • Is same DTC present?
 Yes Replace PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION .)
No Go to the next step.
11 VERIFY AFTER REPAIR PROCEDURE 
 Yes Go to the applicable DTC inspection.
(See DTC TABLE .)
No Troubleshooting completed.
(1) California emission regulation applicable ATX model
(2) Except for California emission regulation applicable ATX model
scientia non olet · About LEMON Manuals