Diagnostic procedure

WARNING: This page is about a different car, the 2005 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.

DTC P0704 [L3] DIAGNOSTIC PROCEDURE

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDED Has FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
1		No	Record FREEZE FRAME DATA on repair order, then go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Check for related Service Bulletins and/or online repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	CLASSIFY HIGH INPUT OR LOW INPUT Connect WDS or equivalent to DLC-2. Access CPP PID. Verify CPP PID during clutch pedal operation. Is CPP PID always OFF?.	Yes	Go to Next step.
3		No	Go to Step 10.
4	INSPECT CLUTCH PEDAL POSITION SWITCH CONNECTOR FOR POOR CONNECTION Turn ignition switch to OFF. Disconnect clutch pedal position switch connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 14.
4		No	Go to the next step.
5	CLASSIFY CLUTCH PEDAL POSITION SWITCH OR CIRCUIT Connect WDS or equivalent to DLC-2. Access CPP PID. Connect a jumper wire between clutch pedal position switch terminal B and D (harness-side). Is CPP PID on?	Yes	Go to the next step.
5		No	Go to Step 7.
6	INSPECT CLUTCH PEDAL POSITION SWITCH Perform clutch pedal position switch inspection. (See CLUTCH PEDAL POSITION (CPP) SWITCH INSPECTION .) Is clutch pedal position switch normal?	Yes	Go to Step 14.
6		No	Replace clutch pedal position switch, then go to Step 14.
7	INSPECT CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT FOR OPEN CIRCUIT Inspect continuity between clutch pedal position switch terminal D (harness-side) and ground. Is there continuity?	Yes	Go to the next step.
7		No	Repair or replace clutch pedal position switch power circuit for open circuit, then Go to Step 14.
8	INSPECT PCM CONNECTOR FOR POOR CONNECTION Turn ignition switch to OFF. Disconnect PCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 14.
8		No	Go to the next step.
9	INSPECT CLUTCH PEDAL POSITION SWITCH SIGNAL CIRCUIT FOR OPEN CIRCUIT Inspect continuity between clutch pedal position switch terminal B (harness-side) and PCM terminal 1R (harness-side). Is there continuity?	Yes	Repair or replace harness for open circuit, then go to Step 14.
9		No	Go to Step 14.
10	INSPECT CLUTCH PEDAL POSITION SWITCH CONNECTOR FOR POOR CONNECTION Turn ignition switch to OFF. Disconnect clutch pedal position switch connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Is there any malfunction?	Yes	Repair or replace the terminal, then go to Step 14.
10		No	Go to the next step.
11	CLASSIFY CLUTCH PEDAL POSITION SWITCH OR CIRCUIT Connect WDS or equivalent to DLC-2. Access CPP PID. Verify that CPP PID changes from ON to OFF when clutch pedal position switch connector disconnected. Does CPP PID change from ON to OFF?	Yes	Go to the next step.
11		No	Go to Step 13.
12	INSPECT CLUTCH PEDAL POSITION SWITCH Perform clutch pedal position switch inspection. (See CLUTCH PEDAL POSITION (CPP) SWITCH INSPECTION .) Is clutch pedal position switch normal?	Yes	Go to Step 14.
12		No	Replace clutch pedal position switch, then go to Step 14.
13	INSPECT CLUTCH PEDAL POSITION SWITCH SIGNAL CIRCUIT FOR SHORT TO GROUND Inspect continuity between clutch pedal position switch terminal B and ground. Is there continuity?	Yes	Repair or replace harness for short to ground, then go to Step 14.
13		No	Go to Next step.
14	VERIFY TROUBLESHOOTING OF DTC P0704 COMPLETED Make sure to reconnect all disconnected connectors. Start engine. Clear the DTC from the PCM memory using the WDS or equivalent. Operate clutch pedal during drive vehicle below 30 km/h {19 mph} 8 times alternately. Is PENDING CODE for this DTC present?	Yes	Replace PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION .)
14		No	Go to the next step.
15	VERIFY AFTER REPAIR PROCEDURE Perform the "After Repair Procedure". (See AFTER REPAIR PROCEDURE .) Is any DTC present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE .)
15		No	Troubleshooting completed.