LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2002 >> Tribute LX, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 177 (On-Board Diagnostic [Automatic Transaxle Ja5A-El)) >> After Repair Procedure

After Repair Procedure

WARNING: This page is about a different car, the 2004 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
  • After repairing a malfunction, perform this procedure to verify that the malfunction has been corrected.
  • When this procedure is carried out, be sure to drive the vehicle at lawful speed and pay attention to the other vehicles.
  1. Connect the WDS or equivalent to the DLC-2.
  2. Turn the ignition switch to ON (engine off).
  3. Select the clear code function and clear the DTC.
  4. Perform the following trouble code inspections to ensure that the DTC has been resolved:
    • For P0705
      1. Start the engine.
      2. Warm up the engine to normal operating temperature.
      3. Depress the brake pedal, and shift the selector lever from P to D for 5 seconds or more. 
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  i to step  iii again.
      7. Go to Step  5.
    • For P0706
      1. Start the engine.
      2. Warm up the engine to normal operating temperature.
      3. Depress the brake pedal, and shift the selector lever from P to D for 100 seconds or more. 
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  i to step  iii again.
      7. Go to Step  5.
    • For P0711
      1. Decrease ATF temperature to 20 °C (68 °F) or below. 
      2. Start the engine.
      3. Drive the vehicle in D range for 330 seconds or more. 
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  ii to step  iii again.
      7. Go to Step  5.
    • For P0712
      1. Start the engine.
      2. Warm up the engine to normal operating temperature.
      3. Drive the vehicle in D range for 150 seconds or more. 
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  i to step  iii again.
      7. Go to Step  5.
    • For P0713
      1. Start the engine.
      2. Warm up the engine to normal operating temperature.
      3. Drive the vehicle, two separate times, in D range at 20 km/h (12 mph) or above  for 150 seconds or more. 
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  i to step  iii again.
      7. Go to Step  5.
    • For P0715, P0791
      1. Start the engine.
      2. Drive the vehicle under the following conditions for 2 seconds or more. 
        • Vehicle speed (VSS PID): 40 km/h (25 MPH) Or Above 
        • Engine speed (RPM PID): 1,500 RPM Or Above. 
        • Selector lever position: D range
      3. Gradually slow down and stop the vehicle.
      4. Turn the IG switch to OFF.
      5. Repeat from step  ii again.
      6. Go to Step  5.
    • For P0720
      1. Start the engine.
      2. Warm up the engine and ATX.
      3. Drive the vehicle, two separate times, under the following conditions for 2 seconds or more. 
        • Selector lever position: D range
        • Vehicle speed (VSS PID): 40 km/h (25 MPH) 
        • Engine speed (RPM PID): 1,400 RPM Or Above 
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  i to step  iii again.
      7. Go to Step  5.
    • For P0740
      1. Start the engine.
      2. Warm up the engine and ATX.
      3. Drive the vehicle under the following conditions for 10 seconds or more. 
        • Vehicle speed (VSS PID): 76 km/h (47 mph) 
        • Selector lever position: D range
        • TCC operating
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  i to step  iii again.
      7. Go to Step  5.
    • For P0743
      1. Start the engine.
      2. Warm up the engine and ATX.
      3. Drive the vehicle in D range and make sure that the gears shift smoothly from 1 GR to 5GR and TCC is operated.
      4. Go to Step 5.
    • For P0748, P0751, P0752, P0756, P0757, P0761, P0762
      1. Start the engine.
      2. Warm up the engine and ATX.
      3. Drive the vehicle in D range and make sure that the gears shift smoothly from 1 GR to 5GR.
      4. Gradually slow down and stop the vehicle.
      5. Turn the IG switch to OFF.
      6. Repeat from step  i to step  iii again.
      7. Go to Step  5.
    • For P0753, P0758, P0763, P0768, P0773, P0778, P0798, P1710
      1. Start the engine.
      2. Warm up the engine and ATX.
      3. Drive the vehicle in D range and make sure that the gears shift smoothly from 1GR to 5GR.
      4. Go to Step  5.
  5. Gradually slow down and stop the vehicle.
  6. Make sure that no DTCs occur.
scientia non olet · About LEMON Manuals