| GAGE |
Activates Gauge Sweep Of All Gauges, Then Displays Present Gauge Values. Carries Out Checksum Test On ROM & EEPROM |
| All Segments Illuminated |
Illuminates All Odometer Segments |
| BULB |
Illuminates All Micro-Controlled Lights & LEDs (Low Fuel, O/D OFF, MIL, THEFT, Seat Belt, BRAKE, ABS, Low Coolant (3.0L Engine) and Charge ( 2.0L Zetec Engine). Replace Bulb or LED As Necessary |
| r |
Returns To Normal Operation All Micro-Controlled Lights & LEDs. Displays Hexadecimal Value For ROM Level |
| NR |
Displays Hexadecimal Value For ROM Level & Type |
| EE |
Displays Hexadecimal Value For EE Level |
| DT |
Displays Hexadecimal Code For Final Manufacturing Date |
| CF1 |
Displays Hex Coding For First Byte Of Module Configuration Settings. Speedometer Scaling 0=5% Bias, 1=2% Bias, Overspeed Warning 1=Enabled, Overspeed Trip Point 0=62 MPH, 1=74 MPH, ABS Option 1=Present, Reverse Warning 1=Enabled, Seat Belt Chime 1=Enabled, Seat Belt Timeout 0=None, 1=0-60 Seconds, THEFT Indicator 1=Flash With Key Off |
| CF2 |
Displays Hex Coding Of Second Byte Of Module Configuration Settings. Transmission Type 0=Automatic Transmission, 1=Manual Transmission, Seat Belt Telltale 1=Enabled, Key Reminder Chime 1=Enabled, Engine Type 1=3.0L Engine, 0=2.0L Zetec Engine |
| CF3 |
Not Currently Used |
| CF4 |
Not Currently Used |
| CF5 |
Displays Hex Coding Of NVM Module Configuration Settings. Dimming Enabled/Disabled 1=Enabled, RH/LH Drive 1=RH Drive, Rear/Front Defog 1=Front Defog, English/Metric Odometer 1=English |
| DTC #### |
Displays Continuous DTCs. Pressing Reset Button Will Display Any DTCs Stored Before Proceeding To Next Step |
| E ####.# |
Displays English Speed Value Being Input, Speedometer Will Indicate Present Speed |
| Blank #### |
Displays Metric Speed Value Being Input, Speedometer Will Indicate Present Speed |
| t #### |
Displays Tachometer Value Being Input To Instrument Cluster. Tachometer Will Indicate Present Speed. Display Will Show "0" If Input Is Not Received, If Input Received Is Invalid For One Second Or More, Or If Speed Is Zero |
| F ### |
Displays Present Fuel Level Being Input To Instrument Cluster As A Ration. If Value Displayed is 255, Circuit Is Open. If Value Displayed Is 000-009, Circuit Is Shorted. Normal Range Will Be 10-254. If Value Displayed Is 250, Gauge Should Read Full. If Value Displayed Is 30, Gauge Should Read Empty |
| FP ### |
Displays Present Fuel Level Percent Status In Decimal. Display Will Read 0-254 For Normal Range, With 255 Indicating An Open Or Short |
| ### C |
Displays Last Temperature Gauge Input From SCP (J1850) Line. Temperature Gauge Will Indicate Present Temperature In Degrees Celsius |
| odo ### |
Displays Odometer Input Received Through SCP (J1850) Line In A Value From 0 To 254. A Value Reading Of 255 Indicates Invalid Data |
| tr |
Displays Trip Odometer Values In Miles |
| Ebd |
Displays ABS EBD Input Or ABS Command For Brake Warning O=Fail, G=OK, nc=Option Not Present |
| ABS |
Displays ABS TT Input or ABS Warning Command O=Fail, G=OK, nc=Option Not Present |
| bAT ##.# |
Will Indicate Present Battery Voltage |
| HSd |
Displays Present Status Of High Voltage Shutdown 0=Voltage Not High, 1=Over Voltage Shutdown |
| tnS |
Displays TNS Switch Input b=On B+, O=Off |
| d ### |
Displays Present Dimming Switch Input (64=Dim Up, 64-190=Dim Down, 190=No Change, nc=Not Configured) |
| rhS ## |
Display Of Cluster Dimming Step Values From 0-21, 0=Dimming Off, nc=No Dimming For Vehicle |
| iin |
Displays Input Status Of Key-In Ignition Switch b=Key-In B+, O=Key Out, nc=Key-In Chime Disabled |
| HLP |
Displays Input Status Of Headlight Switch G=Headlights On, O=Headlights Off, nc+ Not Configured (Rear Defog Disabled) |
| door |
Displays Input Status Of Door Ajar Switch G=Door Ajar, O=Door Closed |
| Stbt |
Displays Input Status Of Seat Belt G=Seat Belt Not Attached, O=Seat Belt Attached, nc=Seat Belt Telltale Disabled |
| FFOG |
Displays Input Status Of Front Fog Switch b=Front Fog Switch Pressed (B+), O=Front Fog Switch Not Pressed, nc=Not Configured |
| rFOG |
Displays Input Status Of Rear Fog Switch G=Rear Fog Switch Pressed (B+), O=Rear Fog Switch Not Pressed, nc=Not Configured |
| FOGF |
Displays Input Status Of Fog Relay Overcurrent Feedback Circuit When Fog Relay Is Commanded On =Relay Not Commanded, O=Fog Relay Output Short To B+ Or Overcurrent, nc=Not Configured (Rear Fog Disabled) |
| Prnd |
Displays Hexadecimal Value For PRNDL For 1st Gear, 2nd Gear, Drive, Neutral, Reverse And Park |
| paR |
Displays Input Status Of Park Switch G=Park, O=Not Park, nc=Manual Transmission configured |
| Cr |
RUN/START Sense Circuit Check, b=Input High (B+), O=Input Low (Open) |
| AC |
RUN/ACC Sense Circuit Check, b=Input High (B+), O=Input Low (Open) |
| ArbC |
Displays Input Status Of Air Bag Chime Request, G=Air Bag Chime On, O=Air Bag Chime Off |
| Ch |
Displays Either Chime Last Sounded By Cluster Or Chime Presently Sounding, A=Air Bag Chime, b=Beltminder, h=Headlights On, I=Key-In Ignition, O=Overspeed, r=Reverse Gear, S=Seat Belt, t=Trip Select/Reset, =None |
| CHE ## |
Displays 8 Bit Hexadecimal Value Of SCP Check Engine (MIL) Telltale Command =SCP Message Timeout (5 Seconds) Or Received At SCP Initial With Invalid Data, $01=Off, $02=On. $03=Flash, ($04-$FE)=Not Valid Data, $FF=Invalid |
| LCL-X |
Displays Input Status Of Low Coolant Level Switch (3.0L Engine Only) G=Coolant Level Low, O=Coolant Level Okay |
| CS XX |
Displays Last SCP Charging System State Status Received =Status Not Received At Key On Or Received At SCP Initial With Invalid Data, $20=OK-Engine On (TT On), $21=OK-Engine Off (TT Off), $22=Low Voltage (TT On), $23=High Voltage (TT On), $24=Generator Fault-Not Charging (TT On), $25=Generator Fault-Charging (TT On), nc=Not Configured (V6) |
| thFt |
Displays Hexadecimal Data Of Vehicle Security Visual Indicator Command SCP Line Message From PCM |
| od |
Displays Last SCP Overdrive Off Telltale Command Received |
| CC |
Not Used |
| PA-PD |
Displays 8-Bit Hexadecimal Value For Port A-D Readings |
| PE0-PE7 |
Displays 8-Bit Hexadecimal Value For Port E0-E7 Readings |
| PF-PH |
Displays 8-Bit Hexadecimal Value For Port F-PH Readings |