Diagnostic Trouble Code (DTC) Chart
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| HUD | U0100:00 | Lost Communication With ECM/PCM 'A': No Sub Type Information | GO to Pinpoint Test K |
| HUD | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test K |
| HUD | U0146:00 | Lost Communication With Serial Data Gateway 'A': No Sub Type Information | GO to Pinpoint Test K |
| HUD | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test K |
| HUD | U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test K |
| HUD | U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test K |
| HUD | U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test L |
| HUD | U0423:56 | Invalid Data Received from Instrument Panel Cluster Control Module: Invalid/Incompatible Configuration | GO to Pinpoint Test M |
| HUD | U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | GO to Pinpoint Test L |
| HUD | U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | GO to Pinpoint Test L |
| HUD | U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test L |
| HUD | U0429:81 | Invalid Data Received From Steering Column Control Module: Invalid Serial Data Received | GO to Pinpoint Test L |
| HUD | U0557:00 | Invalid Data Received From Front Controls Interface Module 'A': No Sub Type Information | GO to Pinpoint Test L |
| HUD | U0557:81 | Invalid Data Received From Front Controls Interface Module 'A': Invalid Serial Data Received | GO to Pinpoint Test L |
| HUD | U0557:82 | Invalid Data Received From Front Controls Interface Module 'A': Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test L |
| HUD | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test N |
| HUD | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test O |
| HUD | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test O |
| HUD | U3000:46 | Control Module: Calibration/Parameter Memory Failure | GO to Pinpoint Test O |
| HUD | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test P |
| HUD | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test Q |
| HUD | U300A:64 | Ignition Switch: Signal Plausibility Failure | GO to Pinpoint Test R |
| SCCM | B1380:11 | Steering Wheel Right Switch Pack: Circuit Short To Ground | GO to Pinpoint Test A |
| SCCM | B1380:13 | Steering Wheel Right Switch Pack: Circuit Open | GO to Pinpoint Test A |
| SCCM | B1380:4A | Steering Wheel Right Switch Pack: Incorrect Component Installed | GO to Pinpoint Test A |
| SCCM | B1380:96 | Steering Wheel Right Switch Pack: Component Internal Failure | GO to Pinpoint Test A |
| SCCM | B1380:9E | Steering Wheel Right Switch Pack: Stuck On | GO to Pinpoint Test A |