LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2021 >> Nautilus Base, FWD >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Fuel System - General Information - 2.0L ECOBOOST (184KW/250PS) - Mi4 >> General Procedures >> Quick Release Coupling

Quick Release Coupling

For information on Ford Color Coded Illustrations refer to OEM COLOR CODING

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 1 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621117Courtesy of FORD MOTOR COMPANY
GFD621118Courtesy of FORD MOTOR COMPANY

Connect 

  1. Push the quick release coupling onto the tube.
    GFD621119Courtesy of FORD MOTOR COMPANY
  2. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    Press the retainer clip into the quick release coupling body until flush and the tabs are locked in place.

    GFD621120Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 2 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    GFD621121Courtesy of FORD MOTOR COMPANY
    GFD621122Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD621123Courtesy of FORD MOTOR COMPANY
    GFD621124Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 3 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    GFD621125Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD621126Courtesy of FORD MOTOR COMPANY
    GFD621127Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 4 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    GFD621128Courtesy of FORD MOTOR COMPANY
    GFD621129Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD621130Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 5 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    GFD621131Courtesy of FORD MOTOR COMPANY
    GFD621132Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD621133Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 6 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
  3. Press the tabs of the rear retainer clip and pull it to the outward position.
GFD621134Courtesy of FORD MOTOR COMPANY
GFD621135Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick release coupling to make sure it is securely fastened.
    GFD621136Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 7 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621137Courtesy of FORD MOTOR COMPANY
GFD621138Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick connect coupling to make sure it is securely fastened.
    GFD621139Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 8 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    GFD621131Courtesy of FORD MOTOR COMPANY
    GFD621132Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD621133Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 9 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    1. Release the secondary locking tab.
    2. Depress the primary locking tab.
    3. Separate the quick release coupling from the tube.
GFD621140Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Lock the secondary locking tab.

    GFD621141Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 10 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    1. Push on the locking tab.
    2. Lift the clip.
    GFD621142Courtesy of FORD MOTOR COMPANY
    1. Depress the tabs inward.
    2. Push the clip downward.
    3. Separate the quick release coupling from the fuel line.
GFD621143Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. Push the clip down into the quick release coupling.
    3. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD621144Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 11 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621145Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621145Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 12 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621146Courtesy of FORD MOTOR COMPANY
GFD621147Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621148Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 13 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621149Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621150Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 14 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    GFD621151Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD621152Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 15 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Press both retaining tabs inward and remove quick release coupling from fuel tube.
GFD621153Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Inspect and clean both quick release coupling ends.

    Install the quick release coupling onto the tube until it is fully seated.

    GFD621154Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 16 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621155Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621155Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 17 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621156Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621157Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 18 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621158Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621159Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 19 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621160Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621161Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 20 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621162Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621163Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 21 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621164Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621165Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 22 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    GFD621166Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD621167Courtesy of FORD MOTOR COMPANY
  3. GFD621168Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  4. NOTE: Make sure that all fuel connections are checked for leaks.
    NOTE: This step is only necessary if a new component is installed.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD621169Courtesy of FORD MOTOR COMPANY
  5. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 23 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621170Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD621171Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 24 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
GFD621172Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621173Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 25 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    1. Depress the clip into the quick release coupling.
    2. Separate the quick release coupling from the tube.
GFD621174Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621175Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 26 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
    1. Remove the quick release coupling from the tube.
GFD621176Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621177Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 27 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.7L EcoBoost (238kW/324PS) (414-01 Battery, Mounting and Cables - 3.5L EcoBoost (272kW/370PS)).
    GFD621178Courtesy of FORD MOTOR COMPANY
  3. Remove the quick release coupling from the tube.
GFD621179Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD621180Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: BATTERY CABLES - 2.0L ECOBOOST (184KW/250PS) - MI4 .
scientia non olet · About LEMON Manuals