LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2021 >> Aviator Base, AWD >> Repair and Diagnosis >> Electrical >> Gauges >> Instrumentation, Message Center And Warning Chimes (2 Of 2) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test X : The Mil (Malfunction Indicator Lamp) Is Never Or Always On

Pinpoint Test X : The Mil (Malfunction Indicator Lamp) Is Never Or Always On

  1. Normal Operation and Fault Conditions 

    See MIL. REFER to: Instrument Panel Cluster (IPC) - System Operation and Component Description .

    If the MIL request message is missing or invalid for less than 5 seconds, the IPC defaults the MIL to its last state (on or off) based upon the last known good message received.

    If the MIL request message is missing for 5 seconds or longer, the IPC defaults the MIL on.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    PCM P0522:00 Engine Oil Pressure Sensor/Switch "A" Circuit Low: No Sub Type Information Sets in the PCM when the PCM detects a short to ground on the hardwired input from the engine oil pressure sensor.
    PCM P0523:00 Engine Oil Pressure Sensor/Switch "A" Circuit High: No Sub Type Information Sets in the PCM when the PCM detects an open on the hardwired input from the engine oil pressure sensor.

    Possible Sources 

    • Wiring, terminals or connectors
    • Instantaneous invalid sensor signal
    • Engine oil pressure (EOP) sensor
    • Communication concern
    • GWM
    • PCM
    • IPC

  2. X1 CHECK THE ENGINE OIL PRESSURE SENSOR STATUS

    NOTE: Make sure the engine temperature is warm or hot when performing this step.

    • Ignition ON.

    • Using a diagnostic scan tool, view PCM Parameter Identifications (PIDs).

    • Access the PCM and monitor the EOP_URPID

    Is an engine oil pressure sensor circuit fault present? 

    Yes  GO to  X6
    No  GO to  X2

  3. X2 PERFORM THE PCM (POWERTRAIN CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the PCM self-test.

    • Check for recorded Diagnostic Trouble Codes (DTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  For DTC P0522:00 and P0523:00, GO to  X6 For all other Diagnostic Trouble Codes (DTCs), REFER to the Master DTC Chart.
    No  GO to  X3

  4. X3 CHECK THE MESSAGE CENTER OPERATION

    • Ignition ON.

    • Close all doors, liftgate and hood.

    • Clear all message center warnings by pressing the OK button for each warning present.

    • Monitor the door ajar RTT warning indicator.

    • Open the driver door.

    • Clear the message center popup warning.

    • Monitor the door ajar RTT warning indicator.

    Is the door ajar RTT warning indicator off with the door closed, and on with the door open? 

    Yes  GO to  X4
    No  GO to Pinpoint Test A 

  5. X4 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Ignition ON.

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to the IPC DTC Chart. Refer to Diagnostic Trouble Code (DTC) Chart 
    No  GO to  X5

  6. X5 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (DTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Communications Network .
    No  If the MIL is never on, the system is operating correctly at this time. If the MIL is always on, DIAGNOSE all PCM Diagnostic Trouble Codes (DTCs). For DTC P0522:00 or P0523:00, GO to  X6 For all other Diagnostic Trouble Codes (DTCs), REFER to the Master DTC Chart.

  7. X6 CHECK FOR VOLTAGE AT THE ENGINE OIL PRESSURE SENSOR

    • Ignition OFF.

    • Disconnect Engine Oil Pressure Sensor C1636.

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1636-3
      GFD533644Courtesy of FORD MOTOR COMPANY
      		 Refer to C1636-2

    Is the voltage approximately 5 volts? 

    Yes  GO to  X7
    No  GO to  X10

  8. X7 CHECK THE ENGINE OIL PRESSURE SENSOR SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE

    • Ignition OFF.

    • Disconnect PCM C1551E.

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1551E-69
      GFD533644Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the circuit.
    No  GO to  X8

  9. X8 CHECK THE ENGINE OIL PRESSURE SENSOR SIGNAL CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1551E-69
      GFD533644Courtesy of FORD MOTOR COMPANY
      		 Refer to C1636-1

    Is the resistance less than 3 ohms? 

    Yes  GO to  X9
    No  REPAIR the circuit.

  10. X9 CHECK THE ENGINE OIL PRESSURE SENSOR SIGNAL CIRCUIT FOR A SHORT TO GROUND

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1636-1
      GFD533656Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance greater than 10, 000 ohms? 

    Yes  INSTALL a new engine oil pressure sensor. REFER to the appropriate Electronic Engine Controls article. CLEAR the Diagnostic Trouble Codes (DTCs). TEST the system for normal operation. If the MIL or RTT indicator is still never or always on, GO to  X14
    No  REPAIR the circuit.

  11. X10 CHECK THE ENGINE OIL PRESSURE SENSOR VREF CIRCUIT FOR A SHORT TO VOLTAGE

    • Ignition OFF.

    • Disconnect PCM C1551E.

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1636-3
      GFD533644Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the circuit.
    No  GO to  X11

  12. X11 CHECK THE ENGINE OIL PRESSURE SENSOR VREF CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1636-3
      GFD533656Courtesy of FORD MOTOR COMPANY
      		 Refer to C1551E-118

    Is the resistance less than 3 ohms? 

    Yes  GO to  X12
    No  REPAIR the circuit.

  13. X12 CHECK THE ENGINE OIL PRESSURE SENSOR VREF CIRCUIT FOR A SHORT TO GROUND

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1636-3
      GFD533656Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  X13
    No  REPAIR the circuit.

  14. X13 CHECK THE ENGINE OIL PRESSURE SENSOR RETURN CIRCUIT FOR AN OPEN

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C1636-2
      GFD533656Courtesy of FORD MOTOR COMPANY
      		 Refer to C1551E-5

    Is the resistance less than 3 ohms? 

    Yes  INSTALL a new engine oil pressure sensor. REFER to the appropriate Electronic Engine Controls article. CLEAR the Diagnostic Trouble Codes (DTCs). TEST the system for normal operation. If the MIL or RTT indicator is still never or always on, GO to  X14
    No  REPAIR the circuit.

  15. X14 CHECK FOR CORRECT PCM (POWERTRAIN CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the PCM connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the PCM connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present

    Is the concern still present? 

    Yes  CHECK On-Line Automotive Service Information System (OASIS) for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PCM. REFER to the appropriate Electronic Engine Controls article.
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals