Pinpoint Test Cp : U0158:00

Normal Operation and Fault Conditions

REFER to: Communications Network - System Operation and Component Description .

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
IPC U0158:00	Lost Communication With Head Up Display: No Sub Type Information	Sets in continuous memory in the IPC if data messages received from the HUD module are missing for 5 seconds or longer.

Possible Sources

Communication concern
HUD module
IPC

CP1 VERIFY THE CUSTOMER CONCERN

Ignition ON.

Verify there is an observable symptom present.

Is an observable symptom present?

Yes

GO to CP2

No	CLEAR the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

CP2 CHECK THE COMMUNICATION NETWORK
- Using a diagnostic scan tool, perform the network test.
Does the HUD module pass the network test?

Yes GO to CP3

No REFER to: Communications Network .

CP3 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST
- Using a diagnostic scan tool, perform the IPC self-test.
Are any non-network Diagnostic Trouble Codes (DTCs) present?

Yes REFER to DTC Chart: IPC in this information. Refer to Diagnostic Trouble Code (DTC) Chart

No GO to CP4

CP4 PERFORM THE HUD (HEAD UP DISPLAY) MODULE SELF-TEST
- Using a diagnostic scan tool, perform the HUD module self-test.
Are any non-network Diagnostic Trouble Codes (DTCs) present?

Yes REFER to: Instrumentation, Message Center and Warning Chimes - Vehicles With: Head Up Display (HUD) .

No GO to CP5

CP5 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)

Using a diagnostic scan tool, clear the IPC Diagnostic Trouble Codes (DTCs).

Ignition OFF.

Ignition ON.

Wait 10 seconds.

Using a diagnostic scan tool, perform the continuous memory self-test.

Check the IPC Diagnostic Trouble Codes (DTCs).

Is DTC U0158:00 still present?

Yes

GO to CP6

No	The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

CP6 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

NOTE: If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI, or the PMI may not have been carried out.

CHECK the vehicle service history for recent service actions related to the HUD module, GWM or IPC. If recent service history is found:
- verify correct replacement module was installed
  - vehicle parts build may be used to verify correct part fitment
- verify the configuration of replacement module was correct
  - re-configure module using as-built data if prior configuration is suspect
- verify the module was not obtained from a like vehicle and installed into customer vehicle
  - return the swapped module to source vehicle and obtain new replacement module

Operate the system and determine if the observable symptom is still present.

Is the observable symptom still present?

Yes

GO to CP7

No	The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

CP7 CHECK FOR CORRECT HUD (HEAD UP DISPLAY) MODULE OPERATION

Ignition OFF.

Disconnect and inspect all HUD module connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect all the HUD module connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new HUD module. REFER to: Head Up Display (HUD) Module .

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.