A Clutch

WARNING: This page is about a different variant/trim than selected.

Symptom Chart

A clutch

For A clutch operation, REFER to: A Clutch .

A clutch

Condition	Possible Sources	Action
A clutch does not apply	SSA is mechanically stuck off	INSTALL a new solenoid. REFER to: Solenoid (307-01D).
	A clutch control valve stuck off	DISASSEMBLE, CLEAN and INSPECT the clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body (307-01D).
	A CL CONTR, hydraulic circuit blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body (307-01D).
	A clutch piston seals	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).
	A clutch hub / Output sun gear	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).
	A clutch friction plates	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).
A clutch always applied	SSA mechanically stuck	INSTALL a new solenoid. REFER to: Solenoid (307-01D).
	A clutch control valve stuck on	DISASSEMBLE, CLEAN and INSPECT the clutch control valve. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body (307-01D).
	A CL CONTR, hydraulic circuit cross leaks	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for leaks or damage. INSTALL new components as necessary. REFER to: Main Control Valve Body (307-01D).
	A clutch friction plates	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).
A clutch delayed/soft/slipping apply	Incorrect transmission strategy programmed into PCM/ TCM.	PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download (307-01D).
	Low line pressure	PERFORM line pressure test. REFER to: Special Testing Procedures .
	SSA mechanically sticking	INSTALL a new solenoid. REFER to: Solenoid (307-01D).
	A clutch control valve sticking	DISASSEMBLE, CLEAN and INSPECT the valves. If bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body (307-01D).
	A CL CONTR, hydraulic circuits blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body (307-01D).
	A clutch piston seals	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).
	A clutch friction plates	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).
A clutch harsh apply	Incorrect transmission strategy programmed into PCM/ TCM.	PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download (307-01D).
	High line pressure	PERFORM the line pressure test. REFER to: Special Testing Procedures .
	SSA mechanically sticking	INSTALL a new solenoid. REFER to: Solenoid (307-01D).
	A clutch control valve sticking	DISASSEMBLE, CLEAN and INSPECT the valves. If the bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body (307-01D).
	A CL CONTR hydraulic circuit blocked/leaking	DISASSEMBLE and INSPECT the main control valve body and separator plate passages for leaks or damage. INSTALL new components as necessary. REFER to: Main Control Valve Body (307-01D).
	A clutch friction plates	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).
	A clutch piston return springs	INSPECT the components for wear and damage. INSTALL new components as necessary. REFER to: Transmission (307-01D).