BCM DTC Chart

DTC	Description	Action
B10F3:11	Left Front Position Light: Circuit Short to Ground	GO to Pinpoint Test A
B10F3:15	Left Front Position Light: Circuit Short to Battery or Open	If the lamp is inoperative, GO to Pinpoint Test A If the lamp is always on, GO to Pinpoint Test B
B10F4:11	Right Front Position Light: Circuit Short to Ground	GO to Pinpoint Test A
B10F4:15	Right Front Position Light: Circuit Short to Battery or Open	If the lamp is inoperative, GO to Pinpoint Test A If the lamp is always on, GO to Pinpoint Test B
B1444:11	Left Rear Stop/Position Lamp Output: Circuit Short to Ground	If the brake lamp is also inoperative, REFER to: STOPLAMPS . If the parking lamp only is inoperative, Refer to BCM Guided Routine .
B1444:15	Left Rear Stop/Position Lamp Output: Circuit Short to Battery or Open	If the brake lamp is also inoperative or always on, REFER to: STOPLAMPS . If the parking lamp only is inoperative or always on, Refer to BCM Guided Routine .
B1445:11	Rear Park Lamps Output: Circuit Short to Ground	GO to Pinpoint Test A
B1445:15	Rear Park Lamps Output: Circuit Short to Battery or Open	If the lamp is inoperative, GO to Pinpoint Test A If the lamp is always on, GO to Pinpoint Test B
B1448:11	Right Rear Stop/Position Lamp Output: Circuit Short to Ground	If the brake lamp is also inoperative, REFER to: STOPLAMPS . If the parking lamp only is inoperative, Refer to BCM Guided Routine .
B1448:15	Right Rear Stop/Position Lamp Output: Circuit Short to Battery or Open	If the brake lamp is also inoperative or always on, REFER to: STOPLAMPS . If the parking lamp only is inoperative or always on, Refer to BCM Guided Routine .
B149E:11	Left Front Position/Sidemarker: Circuit Short To Ground	GO to Pinpoint Test A
B149E:15	Left Front Position/Sidemarker: Circuit Short To Battery or Open	If the lamp is inoperative, GO to Pinpoint Test A If the lamp is always on, GO to Pinpoint Test B
B149F:11	Right Front Position/Sidemarker: Circuit Short To Ground	GO to Pinpoint Test A
B149F:15	Right Front Position/Sidemarker: Circuit Short To Battery or Open	If the lamp is inoperative, GO to Pinpoint Test A If the lamp is always on, GO to Pinpoint Test B
B14B2:11	Left Position Lamps: Circuit Short To Ground	GO to Pinpoint Test A
B14B2:15	Left Position Lamps: Circuit Short To Battery or Open	If the lamp is inoperative, GO to Pinpoint Test A If the lamp is always on, GO to Pinpoint Test B
B14B3:11	Right Position Lamps: Circuit Short To Ground	GO to Pinpoint Test A
B14B3:15	Right Position Lamps: Circuit Short To Battery or Open	If the lamp is inoperative, GO to Pinpoint Test A If the lamp is always on, GO to Pinpoint Test B
U1000:00	Solid State Driver Protection Active -Driver Disabled: No Sub Type Information	The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. For additional information on BCM Field Effect Transistor (FET) protection, REFER to: MODULE CONTROLLED FUNCTIONS - SYSTEM OPERATION AND COMPONENT DESCRIPTION .
U3000:49	Control Module: Internal Electronic Failure	The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, Refer to BCM Guided Routine . For additional information on BCM Field Effect Transistor (FET) protection, REFER to: MODULE CONTROLLED FUNCTIONS - SYSTEM OPERATION AND COMPONENT DESCRIPTION .
For other BCM Diagnostic Trouble Codes (DTCs)	-	REFER to: BODY CONTROL MODULE (BCM) .