LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2018 >> MKZ Select, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 483 (Information Center - Instrumentation, Message Center, And Warning Chimes) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test Bu : U0424:82 >> Pinpoint Test Bu : U0424:82

Pinpoint Test Bu : U0424:82

WARNING: This page is about a different car, the 2016 Ford Expedition. However, it is still accessible from the selected car via links, so may be relevant.

  1. BU1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.
    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  BU2.
    No  CLEAR the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  2. BU2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform a network test.
    • Carry out the network test.

    Does the HVAC module pass the network test? 

    Yes  GO to  BU3.
    No  REFER to Module Communications Network .

  3. BU3 PERFORM THE HVAC MODULE SELF-TEST

    • Using a diagnostic scan tool, perform the HVAC module self-test

    Are any DTCs recorded? 

    Yes  REFER to Climate Control System General Information and Diagnostics .
    No  GO to  BU4.

  4. BU4 PERFORM THE IPC SELF-TEST

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any voltage related DTCs recorded? 

    Yes  REFER to DTC Chart: IPC .
    No  GO to  BU5.

  5. BU5 RECHECK THE IPC DTCs

    • Clear the DTCs.
    • Wait 10 seconds.
    • Repeat the IPC self-test.

    Is DTC U0424:82 still present? 

    Yes  GO to  BU6.
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  6. BU6 CHECK FOR CORRECT HVAC MODULE OPERATION

    • Ignition OFF.
    • Disconnect and inspect the HVAC module connectors.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the HVAC module connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs address this concern, INSTALL a new HVAC module. REFER to Climate Control System General Information and Diagnostics .CLEAR the DTC. REPEAT the self-test. If DTC U0424:82 is still present, GO to  BU7.
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  7. BU7 CHECK FOR CORRECT IPC OPERATION

    • Ignition OFF.
    • Disconnect and inspect the IPC connector.
    • Repair:
      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary
    • Reconnect the IPC connector. Make sure it seats and latches correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs address this concern, Refer to IPC Hardware Testing .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals