DTC Chart: HCM
WARNING: This page is about a different car, the 2018 Ford Focus. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
HCM DTC Chart
| DTC | Description | Action |
|---|---|---|
| B1087:83 | LIN Bus "A": Value of Signal Protection Calculation Incorrect | GO to Pinpoint Test G |
| B1087:86 | LIN Bus "A": Signal Invalid | GO to Pinpoint Test G |
| B1088:83 | LIN Bus "B": Value of Signal Protection Calculation Incorrect | GO to Pinpoint Test G |
| B1088:86 | LIN Bus "B": Signal Invalid | GO to Pinpoint Test G |
| B11F1:54 | Swiveling Control: Missing Calibration | INSTALL a new headlamp assembly. REFER to: Headlamp Assembly . |
| B1C98:11 | Left Hand Corner Lamp Circuit: Circuit Short To Ground | REFER to: Turn Signal and Hazard Lamps . |
| B1C98:13 | Left Hand Corner Lamp Circuit: Circuit Open | REFER to: Turn Signal and Hazard Lamps . |
| B1C99:11 | Right Hand Corner Lamp Circuit: Circuit Short To Ground | REFER to: Turn Signal and Hazard Lamps . |
| B1C99:13 | Right Hand Corner Lamp Circuit: Circuit Open | REFER to: Turn Signal and Hazard Lamps . |
| B1D64:01 | Left Headlamp Swiveling Motor: General Electrical Failure | GO to Pinpoint Test G |
| B1D64:64 | Left Headlamp Swiveling Motor: Signal Plausibility Failure | GO to Pinpoint Test G |
| B1D64:87 | Left Headlamp Swiveling Motor: Missing Message | GO to Pinpoint Test G |
| B1D65:01 | Right Headlamp Swiveling Motor: General Electrical Failure | GO to Pinpoint Test G |
| B1D65:64 | Right Headlamp Swiveling Motor: Signal Plausibility Failure | GO to Pinpoint Test G |
| B1D65:87 | Right Headlamp Swiveling Motor: Missing Message | GO to Pinpoint Test G |
| B1D68:64 | Left Headlamp Swiveling Feedback Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| B1D69:64 | Right Headlamp Swiveling Feedback Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test H |
| U0001:88 | High Speed CAN Communication Bus: Bus off | A HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the diagnostic scan tool. CLEAR the DTC. REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test I |
| U0126:00 | Lost Communication With Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test J |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test K |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test L |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new HCM. |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) and Stability Control . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . |
| U0428:00 | Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the SASM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SASM and other modules on the network. REFER to: Anti-Lock Brake System (ABS) and Stability Control . |
| U053B:00 | Invalid Data Received From Image Processing Module A: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the IPMA. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the IPMA and other modules on the network. REFER to: Lane Keeping System . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new HCM. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new HCM. |
| U3000:45 | Control Module: Program Memory Failure | CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new HCM. |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new HCM. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test M |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test N |