Fcdim Dtc Chart
WARNING: This page is about a different car, the 2018 Ford Focus. However, it is still accessible from the selected car via links, so may be relevant.
| Dtc | Description | Action |
|---|---|---|
| B10Bd:11 | Multifunctional Switch: Circuit Short To Ground | go To Pinpoint Test U |
| B10Bd:13 | Multifunctional Switch: Circuit Open | go To Pinpoint Test U |
| B10Bd:23 | Multifunctional Switch: Signal Stuck Low | go To Pinpoint Test U |
| C1001:01 | Vision System Camera: General Electrical Failure | Refer To: Parking Aid . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (Ipc) Control Module: No Sub Type Information | go To Pinpoint Test Z |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | go To Pinpoint Test Aa |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | go To Pinpoint Test Ab |
| U0264:00 | Lost Communication With Camera Module-Rear: No Sub Type Information | go To Pinpoint Test Y |
| U2013:87 | Switch Pack: Missing Message | go To Pinpoint Test V |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | Check Vehicle Service History For Recent Service Actions Related To This Module. This Dtc Sets Due To Incomplete Or Incorrect Programmable Module Installation (Pmi) Procedures. If There Have Been Recent Service Actions With This Module, Install As-Built Data From Professional Technician Society (Pts), Following The Diagnostic Scan Tool Instructions Under Module Programming>As-Built. Refer To: Module Configuration - System Operation And Component Description . If There Have Been No Recent Service Actions, Install A New Fcdim To Correct The Failure To Retain Configuration Data. Refer To: front Control/Display Interface Module (Fcdim) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | Check Vehicle Service History For Recent Service Actions Related To This Module. This Dtc Sets Due To Incomplete Or Incorrect Programmable Module Installation (Pmi) Procedures. If There Have Been Recent Service Actions With This Module, Install As-Built Data From Professional Technician Society (Pts), Following The Diagnostic Scan Tool Instructions Under Module Programming>As-Built. Refer To: Module Configuration - System Operation And Component Description . If There Have Been No Recent Service Actions, Install A New Fcdim To Correct The Failure To Retain Configuration Data. Refer To: front Control/Display Interface Module (Fcdim) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | Check Vehicle Service History For Recent Service Actions Related To This Module. This Dtc Sets Due To Incomplete Or Incorrect Programmable Module Installation (Pmi) Procedures. If There Have Been Recent Service Actions With This Module, Install As-Built Data From Professional Technician Society (Pts), Following The Diagnostic Scan Tool Instructions Under Module Programming>As-Built. Refer To: Module Configuration - System Operation And Component Description . If There Have Been No Recent Service Actions, Install A New Fcdim To Correct The Failure To Retain Configuration Data. Refer To: front Control/Display Interface Module (Fcdim) . |
| U3000:41 | Control Module: General Checksum Failure | Clear The Diagnostic Trouble Codes (Dtcs). Wait At Least 10 Seconds. Repeat The Self-Test. If Dtc U3000:41 Is Retrieved Again, Install A New Fcdim. Refer To: front Control/Display Interface Module (Fcdim) . |
| U3000:42 | Control Module: General Memory Failure | Clear The Diagnostic Trouble Codes (Dtcs). Wait At Least 10 Seconds. Repeat The Self-Test. If Dtc U3000:42 Is Retrieved Again, Install A New Fcdim. Refer To: front Control/Display Interface Module (Fcdim) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | go To Pinpoint Test Ad |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | go To Pinpoint Test Ae |