LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2018 >> MKZ Select, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1198 (Automatic Transmission - 6F35) >> Diagnosis And Testing >> Intermediate Clutch Assembly

Intermediate Clutch Assembly

WARNING: This page is about a different car, the 2018 Lincoln MKC. However, it is still accessible from the selected car via links, so may be relevant.

For intermediate (2, 6) clutch operation, REFER to: Transmission Description . REFER to: Intermediate Clutch Assembly .

Condition Possible Sources Action
Intermediate (2, 6) clutch does not apply SSC solenoid filter blocked CLEAN or INSTALL a new solenoid. REFER to: Solenoid .
SSC is mechanically stuck OFF INSTALL a new solenoid. REFER to: Solenoid .
Intermediate (2, 6) clutch regulator valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve. If bore or valve is damaged, INSTALL a new main control. REFER to: Main Control Valve Body .
SSC VBS CB26, CB26 hydraulic circuits blocked or leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Transmission Description .
CB26 hydraulic circuit blocked or leaking DISASSEMBLE and INSPECT the transmission case passages for debris/blockage. CLEAN as necessary. REFER to: Transmission Overhaul .
Rear planetary sun gear and shell assembly INSPECT the sun gear and shell for wear and damage. INSTALL new components necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch piston seal leakage INSTALL a new intermediate (2, 6) clutch piston and seals. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch always applied SSC solenoid O-rings cut/damaged INSTALL a new solenoid. REFER to:Solenoid .
SSC mechanically stuck ON INSTALL a new solenoid. REFER to: Solenoid .
Intermediate (2, 6) clutch regulator valve stuck ON DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve and spring. If bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
VBS CB26, CB26 hydraulic circuits leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for leakage. INSTALL new components as necessary. REFER to: Main Control Valve Body .
Rear planetary sun gear and shell assembly INSPECT the sun gear and shell for damage that would prevent free rotation. INSTALL new components as necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch piston return spring INSPECT the return spring for proper installation or damage. INSTALL new components as necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch delayed/soft/slipping apply Incorrect Transmission Strategy programmed into PCM Remove SSC and record solenoid band number. REFER to: Solenoid . Using the scan tool, verify the correct band number is stored in the PCM. If the band numbers do not match, INSTALL a new SSC with correct band number.
SSC solenoid filter partially blocked or restricted CLEAN or INSTALL a new solenoid. REFER to: Solenoid .
SSC mechanically sticking INSTALL a new solenoid. REFER to: Solenoid .
Intermediate (2, 6) clutch regulator valve sticking DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve. If bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
VBS CB26, CB26 hydraulic circuits blocked or leaking DISASSEMBLE and INSPECT the main control and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Transmission Overhaul .
CB26 supply hydraulic circuit blocked or leaking DISASSEMBLE and INSPECT the transmission case passages for debris/blockage. CLEAN as necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch piston seal leakage INSTALL a new intermediate (2, 6) clutch piston. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch harsh apply Incorrect Transmission Strategy programmed into PCM Remove SSC and record solenoid band number. REFER to: Solenoid . Using the scan tool, verify the correct band number is stored in the PCM. If the band numbers do not match, INSTALL a new SSC with correct band number.
SSC mechanically sticking INSTALL a new solenoid. REFER to: Solenoid .
Intermediate (2, 6) clutch regulator valve sticking DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve and spring. If bore, valve or spring is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
VBS CB26, CB26 hydraulic circuits blocked or leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage/leakage. CLEAN as necessary. REFER to: Main Control Valve Body .
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary. REFER to: Transmission Overhaul .
Intermediate (2, 6) clutch piston return spring INSPECT the return spring for proper installation and damage. INSTALL new components as necessary. REFER to: Transmission Overhaul .
scientia non olet · About LEMON Manuals