DTC Charts
DRIVER DOOR MODULE (DDM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B106E | Solid State Driver Disabled Due to Short Circuit | GO to Pinpoint Test AA . |
| B106F | Module Disabled Due to External Fault | GO to Pinpoint Test AA . |
| B1317 | Battery Voltage High | GO to Pinpoint Test AB . |
| B1318 | Battery Voltage Low | GO to Pinpoint Test AC . |
| B1342 | ECU is Faulted | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is retrieved again, INSTALL a new Driver Door Module (DDM). REFER to Driver Door Module (DDM) . TEST the system for normal operation. |
| B1534 | Memory 1 Switch Circuit Short to Ground | REFER to SEATING . |
| B1538 | Memory 2 Switch Circuit Short to Ground | REFER to SEATING . |
| B1667 | Mirror Driver Up/Down Motor Stalled | REFER to REAR VIEW MIRRORS . |
| B1668 | Mirror Driver Right/Left Motor Stalled | REFER to REAR VIEW MIRRORS . |
| B1733 | Mirror Driver Vertical Switch Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B1737 | Mirror Driver Horizontal Switch Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B1741 | Mirror Passenger Vertical Switch Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B1745 | Mirror Passenger Horizontal Switch Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B2223 | Mirror Driver Drive Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B2320 | Mirror Driver Horizontal Feedback Potentiometer Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B2322 | Mirror Driver Horizontal Feedback Potentiometer Circuit Short To Battery | REFER to REAR VIEW MIRRORS . |
| B2324 | Mirror Driver Vertical Feedback Potentiometer Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B2326 | Mirror Driver Vertical Feedback Potentiometer Circuit Short To Battery | REFER to REAR VIEW MIRRORS . |
| B2477 | Module Configuration Failure | REFER to MODULE CONFIGURATION . |
| B2574 | Drivers Door LOCK Switch Short to Ground | GO to Pinpoint Test H . |
| B2575 | Drivers Door UNLOCK Switch Short to Ground | GO to Pinpoint Test H . |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to Pinpoint Test AD . |
| U2050 | No Application Present | REFER to MODULE CONFIGURATION . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
INSTRUMENT PANEL CLUSTER (IPC) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B109E:42 | Remote Keyless Entry: General Memory Failure | The Smart Junction Box (SJB) limit of 4 integrated keys is reached. PROGRAM a maximum of 4 integrated keys. REFER to programming keys using diagnostic equipment in ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) or ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) - HYBRID . CLEAR the DTCs. REPEAT the self-test. |
| B109E:51 | Remote Keyless Entry: Not Programmed | GO to Pinpoint Test R . |
| B109E:86 | Remote Keyless Entry: Signal Invalid | GO to Pinpoint Test L . |
| All other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |
SMART JUNCTION BOX (SJB) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1138 | Memory Full | The SJB limit of 4 integrated keys is reached. PROGRAM a maximum of 4 integrated keys. REFER to programming keys using diagnostic equipment in ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) or ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) - HYBRID . CLEAR the DTCs. REPEAT the self-test. |
| B1139 | Invalid Transmitter Identification Code | GO to Pinpoint Test L . |
| B1624 | Lamp Keypad Output Open Circuit | GO to Pinpoint Test K . |
| B1626 | Lamp Keypad Output Short Circuit To Ground | GO to Pinpoint Test K . |
| B2276 | Less Than 2 Transmitters Programmed | PROGRAM all of the customer's Integrated Keyhead Transmitters (IKTs) (minimum of 2). REFER to ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) or ANTI-THEFT - PASSIVE ANTI-THEFT SYSTEM (PATS) - HYBRID . TEST the system for normal operation. |
| B2425 | Remote Keyless Entry Out of Synchronization | GO to Pinpoint Test L . |
| B2667 | Liftglass Release Switch Circuit Failure | GO to Pinpoint Test I . |
| B2A25 | Trim Panel Lock Switch Circuit Failure | GO to Pinpoint Test H . |
| B2A26 | Keypad Switch Circuit Failure | GO to Pinpoint Test J . |
| All other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |