LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2012 >> MKZ Hybrid >> Repair and Diagnosis (Single Page) >> Brakes >> Traction Control >> Anti-Lock Brake System And Stability Control >> Diagnosis And Testing >> Anti-Lock Control - Non-Hybrid >> Pinpoint Tests >> Pinpoint Test G: DTCs C1963, C2777, U0151, U0452 and U1901 >> PINPOINT TEST G: DTCs C1963, C2777, U0151, U0452 AND U1901

PINPOINT TEST G: DTCs C1963, C2777, U0151, U0452 AND U1901

WARNING: Never probe the electrical connectors on airbag, Safety Canopy® or side air curtain assemblies. Failure to follow this instruction may result in the accidental deployment of these assemblies, which increases the risk of serious personal injury or death.
WARNING: Never disassemble or tamper with seat belt deployable components, including pretensioners, load limiters and inflators. Never back probe deployable device electrical connectors. Tampering or back probing may cause an accidental deployment and result in personal injury or death.
NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  1. G1 CHECK FOR AN HS-CAN CONCERN WITH THE RCM 
    • Connect the scan tool.
    • Ignition ON.
      • NOTE: The Network Test does not test the dedicated CAN communications between the ABS module and RCM.
    • Using the scan tool, carry out the Network Test.
    • Does the RCM pass the Network Test? 
  2. G2 CHECK FOR CORRECT RCM 
    • Ignition OFF.
      • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Gain access to the RCM and check the part number on the RCM against the part number listed in the master parts catalog. Refer to SUPPLEMENTAL RESTRAINT SYSTEM .
    • Does the part number on the RCM match the part number listed in the master parts catalog? 
  3. G3 CHECK FOR CORRECT ABS MODULE 
    • Enter the following diagnostic mode on the scan tool: Log Viewer.
    • Retrieve and record the ABS module part number from Log Viewer and check the part number on the ABS module against the part number listed in the master parts catalog.
    • Does the part number retrieved from the ABS module match the part number listed in the master parts catalog? 
  4. G4 CHECK THE RCM CONDITION AND INSTALLATION 
    • Depower the Supplemental Restraint System (SRS). Refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Inspect the RCM for cracks in the case, broken anchor tabs, broken electrical connector and correct installation. Refer to Removal and Installation, Restraints Control Module (RCM) in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Is the RCM installed correctly and undamaged? 
      • Yes:  GO to G5.
      • No:  REINSTALL or INSTALL new as necessary. GO to  G13.
  5. G5 CHECK THE DEDICATED CAN CIRCUITS FOR AN OPEN 
    • Disconnect: ABS Module C135.
    • Disconnect: RCM C310B.
    • Measure the resistance between the ABS module C135, harness side and the RCM C310B, harness side as indicated in the following chart:
      ABS Module Circuit RCM
      C135-18 VCA23 (BU/WH) C310B-20
      C135-19 VCA24 (GN/OG) C310B-19
      Fig 1: Checking Dedicated CAN Circuits For Open
      G06257064Courtesy of FORD MOTOR CO.
    • Are the resistances less than 5 ohms? 
      • Yes:  GO to G6.
      • No:  REPAIR the affected circuit(s). CLEAR the DTCs. CYCLE the ignition key. REPEAT the self-test. GO to  G13.
  6. G6 CHECK THE DEDICATED CAN CIRCUITS FOR A SHORT TO GROUND 
    • Measure the resistance between ground and:
      • ABS module C135-19, circuit VCA24 (GN/OG), harness side.
      • ABS module C135-18, circuit VCA23 (BU/WH), harness side.
        Fig 2: Checking Dedicated CAN Circuits For Short To Ground
        G06094511Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10, 000 ohms? 
      • Yes:  GO to G7.
      • No:  REPAIR the affected circuit(s). GO to  G13.
  7. G7 CHECK THE DEDICATED CAN CIRCUITS FOR A SHORT TOGETHER 
    • Measure the resistance between ABS module C135-19, circuit VCA24 (GN/OG), harness side and ABS module C135-18, circuit VCA23 (BU/WH), harness side.
      Fig 3: Checking Dedicated CAN Circuits For Short Together
      G06094510Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10, 000 ohms? 
      • Yes:  GO to G8.
      • No:  REPAIR the affected circuit(s). GO to  G13.
  8. G8 CHECK THE DEDICATED CAN CIRCUITS FOR A SHORT TO VOLTAGE 
    • Ignition ON.
    • Measure the voltage between ground and:
      • ABS module C135-19, circuit VCA24 (GN/OG), harness side.
      • ABS module C135-18, circuit VCA23 (BU/WH), harness side.
        Fig 4: Checking Dedicated CAN Circuits For Short To Voltage
        G06094512Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
      • Yes:  REPAIR the affected circuit(s). GO to  G13.
      • No:  GO to G9.
  9. G9 CHECK RCM TERMINATING RESISTOR 
    • Ignition OFF.
    • Connect: RCM C310B.
    • Measure the resistance between ABS module C135-18, circuit VCA23 (BU/WH), harness side and C135-19, circuit VCA24 (GN/OG), harness side.
      Fig 5: Checking RCM Terminating Resistor
      G06094510Courtesy of FORD MOTOR CO.
    • Is the resistance between 108 and 132 ohms? 
      • Yes:  GO to G10.
      • No:  GO to  G11.
  10. G10 CHECK THE ABS MODULE FOR CORRECT OPERATION 
    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation. Refer to RCM in SUPPLEMENTAL RESTRAINT SYSTEM .
      • inspect ABS module C135 for dirt, corrosion, water intrusion, pushed out, loose or spread terminals and loose or frayed wire connections at terminals.
      • repair any concerns found. Refer to CONNECTOR REPAIR PROCEDURES for schematic and connector information.
    • Connect: All Previously Disconnected Component(s)/Connector(s).
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Enter the following diagnostic mode on the scan tool: Self Test - ABS Module.
    • Do any of the DTCs listed in Normal Operation return? 
      • Yes:  INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE  . GO to  G13.
      • No:  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. GO to  G13.
  11. G11 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system components, sensor electrical connectors and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs can be recorded.
    • If previously directed to repower the SRS, depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B CPA lever/lock for correct operation. Refer to RCM Removal and Installation in SUPPLEMENTAL RESTRAINT SYSTEM .
      • inspect ABS module C135 for dirt, corrosion, water intrusion, pushed out, loose or spread terminals and loose or frayed wire connections at terminals.
      • repair any concerns found. Refer to CONNECTOR REPAIR PROCEDURES for schematic and connector information.
    • Connect: All Previously Disconnected Component(s)/Connector(s).
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Were DTCs U0028:08 and/or U0028:88 retrieved on-demand during self-test? 
      • Yes:  INSTALL a new RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . GO to  G13.
      • No:  In the process of diagnosing the fault, the fault condition has become intermittent.

        CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition frequently. ACTIVATE other systems in the same wire harness. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test  . GO to G12.

  12. G12 CHECK FOR AN INTERMITTENT FAULT 
    • Ignition OFF.
    • Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Disconnect RCM C310B and ABS module C135:
      • inspect connector(s) (including any in-line connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • repair any concerns found. Refer to CONNECTOR REPAIR PROCEDURES for schematic and connector information.
    • Connect: All Previously Disconnected Component(s)/Connector(s).
    • Repower the SRS. Do not  prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Are any RCM DTCs retrieved on-demand during the self-test? 
      • Yes:  REFER to Diagnosis and Testing in SUPPLEMENTAL RESTRAINT SYSTEM .
      • No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test  . GO to G13.
  13. G13 CHECK FOR ADDITIONAL RCM AND ABS MODULE DTCs 
    • Ignition OFF.
      WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Reconnect all SRS components (if previously disconnected).
    • If previously directed to depower the SRS, repower the SRS. Do not  prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM.
    • Enter the following diagnostic mode on the scan tool: Self Test - ABS Module.
    • Were any DTCs retrieved on-demand from the RCM or ABS module during self-test? 
      • Yes:  Do not clear any DTCs until all DTCs have been resolved. GO to the appropriate DTC CHART  and/or SUPPLEMENTAL RESTRAINT SYSTEM for pinpoint test direction.
      • No:  CLEAR all Continuous Memory Diagnostic Trouble Codes (CMDTCs). PROVE OUT the SRS. REFER to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .

        Repair is complete. RETURN the vehicle to the customer.

scientia non olet · About LEMON Manuals