LEMON Manuals: Even more car manuals for everyone
Home >> Lincoln >> 2011 >> MKS EcoBoost >> Repair and Diagnosis (Single Page) >> Brakes >> Traction Control >> Anti-Lock Brake System - Vehicle Dynamic Systems >> Diagnosis And Testing >> Anti-Lock Control >> Pinpoint Tests >> Pinpoint Test B: DTCs C1145, C1155, C1165 and C1175 >> PINPOINT TEST B: DTCs C1145, C1155, C1165 AND C1175

PINPOINT TEST B: DTCs C1145, C1155, C1165 AND C1175

NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: If the ignition is turned ON when one or more wheel speed sensors are disconnected, the ABS module will disable the output to that sensor. Make sure all test connections are made at the wheel speed sensors before turning the ignition ON.
  1. B1 CHECK FOR FAULT REPEATABILITY 
    NOTE: The Active Wheel Speed Sensor Tester cannot be used on vehicles equipped with Active Park Assist.
    • Connect the scan tool.
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Clear the CMDTCs.
    • Drive the vehicle at least 16 km/h (10 mph).
    • Retrieve and document Continuous Memory Diagnostic Trouble Codes (CMDTCs).
    • Is DTC C1145, C1155, C1165 or C1175 retrieved? 
    • Yes  : If the Active Wheel Speed Sensor Tester is available, GO to B2.

      If the Active Wheel Speed Sensor Tester is not available, GO to  B4.

    • No  : INSPECT the wheel speed sensors, wheel speed sensor wiring and wheel speed sensor tone rings. REPAIR or INSTALL new as necessary. If any other DTCs are retrieved, GO to the ABS MODULE DTC TABLE .
  2. B2 CHECK THE ABS MODULE OUTPUT USING THE ACTIVE WHEEL SPEED SENSOR TESTER 
    • Ignition OFF.
    • Disconnect: Suspect Wheel Speed Sensor.
    • Connect the Active Wheel Speed Sensor Tester to the wheel speed sensor connectors.
    • Select the correct system polarity on the tester and turn the tester power switch to the ON position.
    • Ignition ON.
    • Is the module output LED illuminated? 
    • Yes  : GO to B3.
    • No  : GO to  B6.
  3. B3 CHECK THE WHEEL SPEED SENSOR OUTPUT WITH THE ACTIVE WHEEL SPEED SENSOR TESTER 
    • Raise the suspect wheel until it can spin freely. Refer to JACKING & LIFTING article.
    • While monitoring the Active Wheel Speed Sensor Tester, slowly spin the suspect wheel.
    • Do the sensor output LEDs illuminate and flash and is the current overload LED not illuminated? 
    • Yes  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
    • No  : If the current level LED is not illuminated and the sensor output LEDs do not illuminate or if the current level LED is illuminated red, INSTALL a new wheel speed sensor. REFER to WHEEL SPEED SENSOR - FRONT  or WHEEL SPEED SENSOR - REAR . CLEAR the DTCs. REPEAT the self-test.

      If the current level LED is not illuminated and the sensor output LEDs illuminate green, but do not flash, INSPECT the wheel speed sensor tone ring (part of the wheel bearing) and INSTALL new as necessary. If the tone ring is OK, INSTALL a new wheel speed sensor. REFER to WHEEL SPEED SENSOR - FRONT  or WHEEL SPEED SENSOR - REAR . CLEAR the DTCs. REPEAT the self-test.

  4. B4 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR A SHORT TO VOLTAGE 
    NOTE: Both circuits must be checked for each DTC.
    • Ignition OFF.
    • Disconnect: ABS Module C135.
    • Disconnect: Suspect Wheel Speed Sensor.
    • Ignition ON.
    • For DTC C1145, measure the voltage between ground and:
      • ABS module C135-18, circuit VCA05 (GY/VT), harness side.
      • ABS module C135-6, circuit RCA19 (VT), harness side.
        Fig 1: Measuring Voltage Between Ground And ABS Module C135-18, Circuit VCA05 (GY/VT)
        G07813754Courtesy of FORD MOTOR CO.
    • For DTC C1155,  measure the voltage between ground and:
      • ABS module C135-34, circuit RCA17 (YE), harness side.
      • ABS module C135-21, circuit VCA03 (VT/WH), harness side.
        Fig 2: Measuring Voltage Between Ground And ABS Module C135-34, Circuit RCA17 (YE)
        G07813755Courtesy of FORD MOTOR CO.
    • For DTC C1165  , measure the voltage between ground and:
      • ABS module C135-31, circuit RCA20 (BN), harness side.
      • ABS module C135-19, circuit VCA06 (WH/OG), harness side.
        Fig 3: Measuring Voltage Between Ground And ABS Module C135-31, Circuit RCA20 (BN)
        G07813756Courtesy of FORD MOTOR CO.
    • For DTC C1175  , measure the voltage between ground and:
      • ABS module C135-33, circuit VCA04 (BU/OG), harness side.
      • ABS module C135-20, circuit RCA18 (BN/GN), harness side.
        Fig 4: Measuring Voltage Between Ground And ABS Module C135-33, Circuit VCA04 (BU/OG)
        G07813757Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
    • Yes  : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
    • No  : GO to B5.
  5. B5 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR A SHORT TO GROUND 
    NOTE: Both circuits must be checked for each DTC.
    • Ignition OFF.
    • For DTC C1145  , measure the resistance between ground and:
      • ABS module C135-18, circuit VCA05 (GY/VT), harness side.
      • ABS module C135-6, circuit RCA19 (VT), harness side.
        Fig 5: Measuring Resistance Between Ground And ABS Module C135-18, Circuit VCA05 (GY/VT)
        G07813758Courtesy of FORD MOTOR CO.
    • For DTC C1155  , measure the resistance between ground and:
      • ABS module C135-34, circuit RCA17 (YE), harness side.
      • ABS module C135-21, circuit VCA03 (VT/WH), harness side.
        Fig 6: Measuring Resistance Between Ground And ABS Module C135-34, Circuit RCA17 (YE)
        G07813759Courtesy of FORD MOTOR CO.
    • For DTC C1165  , measure the resistance between ground and:
      • ABS module C135-31, circuit RCA20 (BN), harness side.
      • ABS module C135-19, circuit VCA06 (WH/OG), harness side.
        Fig 7: Measuring Resistance Between Ground And ABS Module C135-31, Circuit RCA20 (BN)
        G07813760Courtesy of FORD MOTOR CO.
    • For DTC C1175  , measure the resistance between ground and:
      • ABS module C135-33, circuit VCA04 (BU/OG), harness side.
      • ABS module C135-20, circuit RCA18 (BN/GN), harness side.
        Fig 8: Measuring Resistance Between Ground And ABS Module C135-33, Circuit VCA04 (BU/OG)
        G07813761Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10, 000 ohms? 
    • Yes  : GO to B6.
    • No  : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
  6. B6 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR AN OPEN 
    NOTE: Both circuits must be checked for each DTC.
    • Ignition OFF.
    • Disconnect: ABS Module C135.
    • Disconnect: Suspect Wheel Speed Sensor.
    • For vehicles equipped with Active Park Assist:  Measure the resistance between the ABS module connector, harness side and the suspect wheel speed sensor connector, harness side as indicated in the following table:
      CIRCUIT REFERENCE TABLE

      Wheel Speed Sensor Circuit ABS Module
      DTC C1145 - Wheel Speed Sensor RF Input Circuit Failure 
      C1316-1 VCA05 (GY/VT) C135-18
      C1316-2 RCA19 (VT) C135-6
      DTC C1155 - Wheel Speed Sensor LF Input Circuit Failure 
      C1315-1 VCA03 (VT/WH) C135-21
      C1315-2 RCA17 (YE) C135-34
      DTC C1165 - Wheel Speed Sensor RR Input Circuit Failure 
      C4260-1 VCA06 (WH/OG) C135-19
      C4260-2 RCA20 (BN) C135-31
      DTC C1175 - Wheel Speed Sensor LR Input Circuit Failure 
      C4261-1 VCA04 (BU/OG) C135-33
      C4261-2 RCA18 (BN/GN) C135-20
      Fig 9: Checking Wheel Speed Sensor Circuits For Open (Vehicles Equipped With Active Park Assist)
      G07813762Courtesy of FORD MOTOR CO.
    • For all other vehicles:  Measure the resistance between the ABS module connector, harness side and the suspect wheel speed sensor connector, harness side as indicated in the following table:
      CIRCUIT REFERENCE TABLE

      Wheel Speed Sensor Circuit ABS Module
      DTC C1145 - Wheel Speed Sensor RF Input Circuit Failure 
      C160-1 RCA19 (VT) C135-6
      C160-2 VCA05 (GY/VT) C135-18
      DTC C1155 - Wheel Speed Sensor LF Input Circuit Failure 
      C150-1 RCA17 (YE) C135-34
      C150-2 VCA03 (VT/WH) C135-21
      DTC C1165 - Wheel Speed Sensor RR Input Circuit Failure 
      C426-1 RCA20 (BN) C135-31
      C426-2 VCA06 (WH/OG) C135-19
      DTC C1175 - Wheel Speed Sensor LR Input Circuit Failure 
      C440-1 RCA18 (BN/GN) C135-20
      C440-2 VCA04 (BU/OG) C135-33
      Fig 10: Checking Wheel Speed Sensor Circuits For Open (All Other Vehicles)
      G07813763Courtesy of FORD MOTOR CO.
    • Are the resistances less than 5 ohms? 
    • Yes  : GO to B7.
    • No  : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the ABS self-test.
  7. B7 CHECK FOR SHORTED WHEEL SPEED SENSOR CIRCUITS 
    • Measure the resistance between the suspect wheel speed sensor connector pins, harness side.
    • Is the resistance greater than 10, 000 ohms? 
    • Yes  : GO to B8.
    • No  : REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
  8. B8 CHECK THE ABS MODULE OUTPUT 
    NOTE: The ABS module detects an open circuit condition and disables the voltage to the wheel speed sensor if the ignition is set to the ON position before all test connections are made.
    NOTE: A meter with min/max feature and/or recording capabilities must be used to obtain accurate measurements.
    • Ignition OFF.
    • Connect: ABS Module C135.
    • Connect the meter to the suspect wheel speed sensor electrical connector pins, harness side.
    • Set the meter to DC voltage in a range greater than 15 volts.
    • Enable the min/max feature.
    • Ignition ON.
    • Check the maximum recorded voltage on the meter.
    • Is the maximum recorded voltage greater than 10 volts? 
    • Yes  : GO to  B10.
    • No  : GO to B9.
  9. B9 CHECK FOR CORRECT ABS MODULE OPERATION 
    • Disconnect: ABS Module C135.
    • Check for:
      • corrosion.
      • pushed-out pins.
      • spread terminals.
    • Connect the ABS module connector and make sure it seats correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
    • Yes  : INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . CLEAR the DTCs. REPEAT the self-test.
    • No  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
  10. B10 CHECK FOR CORRECT WHEEL SPEED SENSOR OPERATION 
    • Disconnect: Wheel Speed Sensor Connector.
    • Check for:
      • corrosion.
      • pushed-out pins.
      • spread terminals.
    • Connect the wheel speed sensor connector and make sure it seats correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
    • Yes  : INSTALL a new wheel speed sensor. REFER to WHEEL SPEED SENSOR - FRONT  or WHEEL SPEED SENSOR - REAR . CLEAR the DTCs. REPEAT the self-test.
    • No  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
scientia non olet · About LEMON Manuals