Intermediate Shaft Seal and Deflector: Removal

WARNING: This page is about a different variant/trim than selected.

NOTE: The Power Transfer Unit (PTU) may leak different color fluids, red oil leak for automatic transmission fluid and brown/black gear lube for PTU fluid. The PTU seals prevent these types of fluids from leaking. It is important to note which color fluid is leaking to conduct the most appropriate service procedure. This procedure will correct a red oil leak (automatic transmission fluid) from the intermediate shaft seal on the RH side of the PTU. For additional information, refer to ANALYSIS OF LEAKAGE .

NOTE: This procedure is to be performed through the RH wheel opening. It is not necessary to remove the exhaust components to complete this repair.

With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING AND LIFTING article.
Remove the RH front wheel and tire. For additional information, refer to WHEELS AND TIRES article.
Apply the brake to keep the halfshaft from rotating and remove the front wheel hub nut.
- Do not discard the nut at this time.

Fig 1: Locating Front Wheel Hub Nut

Courtesy of FORD MOTOR CO.

Remove the brake flexible hose bracket bolt and disconnect the hose from the shock absorber.

Fig 2: Identifying Brake Flexible Hose Bracket Bolt

Courtesy of FORD MOTOR CO.

Disconnect the wheel speed sensor harness from the shock absorber bracket.

Fig 3: Identifying Wheel Speed Sensor Harness

Courtesy of FORD MOTOR CO.

Remove the RH brake disc. For additional information, refer to FRONT DISC BRAKE article.

NOTE: Suspension fasteners are critical parts because they affect performance of vital components and systems and their failure may result in major service expense. New parts must be installed with the same part numbers or equivalent part, if replacement is necessary. Do not use a replacement part of lesser quality or substitute design. Torque values must be used as specified during reassembly to make sure of correct retention of these parts.

Remove and discard the upper stabilizer bar link nut.
- Position the stabilizer bar link aside.

Fig 4: Identifying Ball Joint-to-knuckle Bolt And Nut

Courtesy of FORD MOTOR CO.

Remove and discard the ball joint-to-knuckle bolt and nut.
- Separate the lower control arm from the knuckle.

Fig 5: Identifying Ball Joint-to-knuckle Bolt And Nut

Courtesy of FORD MOTOR CO.

Using the Front Wheel Hub Remover, separate the halfshaft from the wheel hub.

Fig 6: Pressing Halfshaft From Wheel Bearing & Hub

Courtesy of FORD MOTOR CO.

Pull the knuckle outboard and rotate it toward the rear of the vehicle.
- Secure the knuckle assembly.

Fig 7: Identifying Knuckle Assembly

Courtesy of FORD MOTOR CO.

NOTE: It is not necessary to separate the halfshaft from the intermediate shaft for this repair.

Remove the 2 intermediate shaft bracket bolts and the intermediate and halfshaft assembly.
- Inspect the intermediate shaft for pitting or damage in the seal contact area. Replace if necessary.

Fig 8: Identifying Bearing Cup Remover

Courtesy of FORD MOTOR CO.

NOTE: The following instruction will prevent the Bearing Cup Remover from opening too far which would make removing the intermediate shaft seal deflector difficult.

Place a 16 mm (5/8 in) washer between the components of the Bearing Cup Remover as shown in illustration.

Fig 9: Identifying 16 mm (5/8 in) Washer

Courtesy of FORD MOTOR CO.

NOTE: Using a 5-pound or larger slide hammer eases the removal of the seal deflector.

Using the Bearing Cup Remover, the extension from the Halfshaft Remover, and a suitable slide hammer, remove the seal deflector.
- The seal deflector will have been damaged during removal. Remove all foreign material from the PTU before continuing with the repair.

Fig 10: Removing Seal Deflector

Courtesy of FORD MOTOR CO.

Using the Bearing Cup Remover, the extension from the Halfshaft Remover, and a suitable slide hammer, remove the intermediate shaft seal, and if equipped, the alignment washer.

Fig 11: Removing Intermediate Shaft Seal

Courtesy of FORD MOTOR CO.